Edmonton Commercial Roof Leak Service, April 2015

This commercial client required an initial inspection followed by minor roof leak repairs on their property. The report briefly describes the work completed and is accompanied by pictures of the repair. Roof Report, April 4, 2015:
Today we fixed 12 spots on the roof that were possible leak areas, along with filling up 2 pitch pockets. All of the rears were gum patches.
20150403_103154_resized 20150403_103159_resized 20150403_103205_resized 20150403_124142_resized 20150403_124150_resized 20150403_124201_resized 20150403_124519_resized 20150403_124645_resized 20150403_125344_resized 20150403_125605_resized 20150403_125702_resized 20150403_125933_resized 20150403_134219_resized 20150403_134232_resized
< End Report > CODE: 13040 Contact Us Call our 24 hour emergency roof repair at 1.780.424.7663. Mail to: 3428 99 Street NW Edmonton, Alberta T6E-5X5. We service all of Alberta including Edmonton, Stony Plain, Spruce Grove, Fort Saskatchewan, St Albert, Sherwood Park, Leduc, Nisku, Beaumont, Lac La Biche, Grande Prairie, High Level, Westlock, Slave Lake, Edson, Drayton Valley, Devon, Camrose, Wetaskiwin, Tofield, Lamont, Morinville, Vegreville, Tofield, Millet, Calmar, Evansburg, Redwater, Onaway, Viking, Athabasca, High Prairie, Valleyview, Fairview, Peace River, Whitecourt, Mayerthorpe and many more rural areas and towns.

Edmonton Commercial Flat Roof Repair, March 2015

This commercial client in Edmonton required a significant amount of repair work to ensure their flat roof would pass inspection. The report follows our initial inspection and the subsequent repair process.
Inspection, March 13, 2015: We met with the client onsite at 10:30 pm to take a look at the BUR roof that needs a 2x2 ft. vent curb deleted and another new curb installed. He would like us to install two sleepers on the roof tied back into the membrane. Two gum boxes are to be installed as well, one for a gas line and one for an electrical line to go through the roof. This a single story with easy access all around the building. We did a cut test and found that the roof is made up of a 3 inch structural strammit with 2 layers of 1/2 inch fiberboard and mopped felt. The problem with this kind of roof is that the vapour barrier is the skin of the strammit and comes in 4x8 sheets. This means that any patch would have to be at least to the nearest truss and be supported with 2x4 boards under the cuts of the strammit opening. For any warrantied work, we should tie in the strammit vapour across the patch and this needs to be done from underneath after the patch is applied. This would also require a 3x3 ft. hole to be cut out of the ceiling and should be handled by the client ahead of time. The other option is to replace a full sheet of strammit which may include a new complete tie in around the next curb beside it (depending on the layout of the strammit). We could just cover the hole with 1 inch plywood using no insulation, then use peel and stick, and torch cap the BUR. I would not suggest warrantying this kind of repair, especially right on top of a large commercial stove. These are improvements to be made to pass inspection to get the restaurant operating again. Another issue is the amount of grease that has been dumped onto the roof. This will require a larger patch since the membrane close to the curb will not support a proper tie in of 2 ply torch patch, and will require a 4 ft. area of membrane to be spudded beyond the patch all the way around. The client has requested another 2 curbs, 1 for an exhaust vent and 1 for an intake vent for the RTU to sit close to the sleeper witch would add another 8 – 10 man hrs. to the job. He has requested that we wrap all 3 curbs with ISO and plywood which brings us up to approximately 50 man hrs. for: 1 deleted curb, 3 new curbs to be installed and wrapped, 2 sleepers, and 2 gum boxes. If the new curb is not prepped ahead of us then we will need another sheet of ISO (size to be determined by flange of curb) and plywood to wrap the curb. If there is no ceiling access when we are there then add another 3 man hrs. to cut out and clean up.
Materials Required:
  • (2) 4x8 sheets of 1 inch plywood.
  • 3 rolls of cap.
  • 3 rolls of torch grade peel and stick.
  • (2) 5 gallon cans of sam adhesive.
  • 2 sheets of 3 inch ISO.
  • (10) 2x6 10 ft. boards.
  • (3) 2x4 8 ft. boards.
  • (2) 4 inch gum boxes
  • 2 pails of gum.
  • Assorted screws.
  • 2 cans of spray primer.
  • 5 paint brushes.
  • 3 roller sleeves.
  • 3 tubes of acoustical sealant.20150318_135912_resized 20150318_135919_resized 20150318_135926_resized 20150318_140109_resized 20150318_140112_resized
Roof Report, March 21, 2015: Today we deleted an old unit and added two curbs for new units. This was a difficult task as the roof is very old and quite frankly falling apart. There was also a section (6ft.x7ft.) that we had to remove because the grease from the grease trap had saturated the roof. Once we had all of this cut out and the insulation and plywood replaced, we roofed in the curbs and the greased section. All that is left to do is torch capping on the curbs and then add two more sleepers and roof them in.
As a side note, there are multiple areas around the added curbs that have positive leaks. There are also splits in the roof and major blisters. I pointed this out to the customer and he said he is aware of the leaks but has to wait for approval from property management before fixing them.
20150331_154733_resized 20150331_154740_resized 20150331_170011_resized 20150331_173004_resized 20150331_173024_resized 20150331_173029_resized 20150331_173911_resized
20150331_091659_resized 20150331_091701_resized 20150331_091704_resized 20150331_135820_resized 20150331_142912_resized 20150331_142932_resized 20150331_154726_resized
Photo Journal, May 30, 2015:
1 2 3 4 5
 This report may be updated at a later time.
< End Report >
CODE: 10625 Contact Us Call our 24 hour emergency roofing repair at 1.780.424.7663. Mail to: 3428 99 Street NW Edmonton, Alberta T6E-5X5. We service all of Alberta including Edmonton, Stony Plain, Spruce Grove, Fort Saskatchewan, St Albert, Sherwood Park, Leduc, Nisku, Beaumont, Lac La Biche, Grande Prairie, High Level, Westlock, Slave Lake, Edson, Drayton Valley, Devon, Camrose, Wetaskiwin, Tofield, Lamont, Morinville, Vegreville, Tofield, Millet, Calmar, Evansburg, Redwater, Onaway, Viking, Athabasca, High Prairie, Valleyview, Fairview, Peace River, Whitecourt, Mayerthorpe and many more rural areas and towns.

Edmonton Commercial Roof Installation Photo Journal, March 2015

This photo journal follows a new commercial construction in Edmonton and the necessary roof installation. The photos illustrate part of the progress made by the GRS crew, however this report may be updated in the future. Materials Required:
  • 525 sheets of fr board.
  • 170 rolls of cap.
  • 30 rolls of armor bond flash.
  • 70 rolls of iko lap.
  • 10 rolls of 180 flam flam.
  • (4) 5 gallon pails of Sam adhesive.
  • 40 boxes of Millennium 2 part adhesive.
  • (5) 3 gallon pails of roof patch gum.
  • (5) 4 inch drains with covers.
  • 1 pail of mod bit primer.
March 12, 2015: 20150312_144255_resized 20150312_144257_resized 20150312_160629_resized 20150312_160633_resized 20150312_160644_resized 20150312_161419_resized 20150312_161424_resized 20150312_161809_resized 20150312_161813_resized 20150312_161818_resized March 18, 2015: 20150318_124237_resized 20150318_124308_resized 20150318_124319_resized 20150318_124343_resized 20150318_124356_resized 20150318_124401_resized 20150318_124404_resized 20150318_124601_resized 20150318_124607_resized April 7, 2015: 20150407_143149_resized 20150407_143255_resized 20150407_143421_resized 20150407_143432_resized 20150407_143519_resized 20150407_143521_resized 20150407_143544_resized 20150407_143619_resized 20150407_143704_resized 20150407_143729_resized 20150407_150209_resized20150407_150230_resized20150407_150731_resized20150407_150747_resized April 8, 2015: IMG_1550 IMG_1552 IMG_1553 IMG_1554 IMG_1555 IMG_1556 IMG_1557 April 10, 2015: IMG_1572 IMG_1573 IMG_1574 IMG_1575 IMG_1576 April 28, 2015: 20150428_143932 20150428_144100 20150428_144136 20150428_144518 20150428_144625 20150428_144641 20150428_144712 20150428_144715 20150428_144738 20150428_144748 20150428_144803 20150428_144819 20150428_144829 20150428_144836 20150428_144952 20150428_145749 20150428_145813 20150428_145825 20150428_145843 IMG_1606 April 29, 2015: IMG_1634 IMG_1635 IMG_1636 IMG_1637 IMG_1638 IMG_1639 May 1, 2015: IMG_1649 IMG_1650 May 13, 2015: IMG_1666 IMG_1667 IMG_1668 May 27, 2015: 20150526_164834_resized_1 20150526_165115_resized 20150526_133837_resized20150526_134733_resized20150526_134806_resized20150526_135725_resized20150526_140507_resized20150526_160949_resized20150526_160955_resized20150526_160957_resized20150526_164814_resized This report may be updated in the future. < End Report > CODE: 9576 Contact Us Call our 24 hour emergency roofing repair at 1.780.424.7663. Mail to: 3428 99 Street NW Edmonton, Alberta T6E-5X5. We service all of Alberta including Edmonton, Stony Plain, Spruce Grove, Fort Saskatchewan, St Albert, Sherwood Park, Leduc, Nisku, Beaumont, Lac La Biche, Grande Prairie, High Level, Westlock, Slave Lake, Edson, Drayton Valley, Devon, Camrose, Wetaskiwin, Tofield, Lamont, Morinville, Vegreville, Tofield, Millet, Calmar, Evansburg, Redwater, Onaway, Viking, Athabasca, High Prairie, Valleyview, Fairview, Peace River, Whitecourt, Mayerthorpe and many more rural areas and towns.

Edmonton Commercial Flat Roof Replacement, January 2015

This commercial client in Edmonton was presented with a quotation for a flat roof replacement. The report follows the crew as they performed the replacement over the course of several months. Scope of Work:
  • Scrape gravel down to existing 4 ply membrane and take down to dispose.
  • Supply and glue down a FR board (1/2 inch fiberboard adhered to a 95 gram sanded poly sheet) and seal all laps.
  • Supply and back torch a 180 gram armour bound peal and stick up walls and all penetrations.
  • Remove and replace any wet insulation.
  • Owners to move and re-position satellite and communication systems.
  • Clean all debris and haul away.
Roof Report, January 21, 2015:
We arrived on site at 2:10 pm and I got set up to continue with the cap stripping. At the same time we were waiting to see what was going to happen with the weather since it was still drizzling. I went through the safety paperwork and then we helped with removing the garbage from the roof and brought it to the bin. 20141212_14051920141212_195820 20141212_195807 20141212_140503 Roof Report, January 23, 2015: After our toolbox meeting we proceeded to install FR board on the upper mechanical roof and did so until the point of satellites in all directions. We then installed peel and stick stripping wherever possible and sopramastic waterproofing in all other protrusions.
Cleaned up and left site at 4:30pm.
20150123_140138 20150123_140146 20150123_140200 20150123_140209 20150123_155431 20150123_155440 20150123_155444 20150123_160117 20150123_160124 20150123_160130
Roof Report, February 12, 2015:
This morning after we were done with the safety reports, we went to the upper roof and continued with the base seal tie in. I had two other crew members remove snow from the entire upper roof while I started to install peel and stick on the curbs. After I was done with the curbs on the north side of the roof, I installed patches over the plates and installed gussets were there were none. I also found several spots that needed patches in the field and repaired as required.
Roof Report, February 14, 2015:
Started to lay in FR board where they moved the satellite towers. Once we got the base done on one I had a crew member start capping it in while myself and another crew member started to base in the next section. Both sections were capped by the end of the day which made the client happy. Then I stayed on site to complete fire watch.
20150214_013512_resized 20150214_022441_resized
Roof Report, February 18, 2015:
This morning we started on completing the NE corner of the roof by installing the last of the FR board. We also started sealing around the curbs and perimeter.
We then moved to the SW corner and completed the base tie in around the satellite and patched plate holes in the area. Fire watch from 3:30pm to 5:30pm.
IMGP2516 IMGP2517 IMGP2518 IMGP2519 IMGP2523 IMGP2527 IMGP2532
Roof Report, February 19, 2013: Once we got to the site we continued with the base tie in around the large curb and the parapet on the SW corner of the upper roof.
Roof Report, March 7, 2015: Today we completed the field cap and most of the DE granulating around the details. Roof Report, March 9, 2015:
Bill and me completed the cap stripping on the upper roof today and need to touch up the gum boxes and granules to finish the SBS on the upper roof. We then completed the curbs on the main roof and started to install the plumbing vents when it started to rain at 3 pm. I am not happy with the large ponding area on the east side of the main roof and would like permission to extend the sump on the east side with a trough through the high spot so that more water drains.  I would have to cut out the FR board from the sump about 1 ft. wide west about 10 ft. to where the water ponds 3 inches at the deepest point. Then tie in the old roof to new torch on roof through the trough. This would require 10 man hours and another roll of cap which would add another 2 years to the life of the cap in that area. Roof Report, March 10, 2015:
Today we installed 8 plumbing vents and touched up the existing plumbing vents with smag and granules. We completed the west drop drain install and reset the air units on the SW corner of the main roof. We then cleaned the entire main roof and downloaded all the garbage. Roof Report, March 11, 2015:
This morning we completed the touch ups on the gum boxes of the upper roof and then started installing the metal around the perimeter of the upper roof and found that we were short one length. On the far east side of the roof there looks to be another piece missing that would cover the electrical lines and 2-18 inch storm collars are gone as well. We installed all the metal that was there and added extra screws and smack pins to make them very solid.
Roof Report, March 12, 2015: After the weekly meeting in the morning we met up at Home Depot for caulking and then went to the site. We spent extra time on resetting all the wire tracks on the upper roof and finished off the storm collars with caulking as well. 2 of the 18 inch stacks still have no storm collars but we filled them with caulking anyway. With no metal flashing on the wall detail on the upper roof, we made sure that water would not pond there by completely filling the riglet with caulking. We downloaded the rest of the tools, rolls of base, and propane into the small trailer and parked it in the very NE corner of the parking lot.  The bin is still on site and will need to be removed.
Follow-up Inspection, August 19, 2015: Upon visual inspection of the roof. I noticed 6 different blisters had developed. Attached is a copy of a roof map that shows the approximate locations of the blisters. Continuing on we walked the entire roof, testing the membrane to make sure the insulation was properly adhered to the roof underneath. I would say that there is no issues with the adhesion. The following is a list of the repairs that should be made to said deficiencies:
  • A lack of chipping away at the existing roof that was re-roofed led to a ridge. We can either build it up around it, leveling it off, or cut it and patch it.
  • Run a patch to meet lapping requirements.
  • Pipes need to be patched.
  • Anchor fasten the flashing correctly to the wall. Ms detail to seal the flashing.
  • Replace with concrete paving stones and roof mate underneath, and have a drainage mat under the roof mate.
  • Run a drainage mat or roof mate.
  • Install storm collars and caulk them.
  • Have a flashing made up and installed.
  • Have a sheet metal cap fabricated and installed.
  • Install cap sheet, roof mate, drainage mat and paving stones.
  • Box it in with cap and quick prime.
20150819_135209 20150819_135233 20150819_135237 20150819_135341 r1 r2 r3 r4 r5 r6 r7 rrrrrr6
< End Report > CODE: 11834 Contact Us Call our 24 hour emergency roof repair at 1.780.424.7663. Mail to: 3428 99 Street NW Edmonton, Alberta T6E-5X5. We service all of Alberta including Edmonton, Stony Plain, Spruce Grove, Fort Saskatchewan, St Albert, Sherwood Park, Leduc, Nisku, Beaumont, Lac La Biche, Grande Prairie, High Level, Westlock, Slave Lake, Edson, Drayton Valley, Devon, Camrose, Wetaskiwin, Tofield, Lamont, Morinville, Vegreville, Tofield, Millet, Calmar, Evansburg, Redwater, Onaway, Viking, Athabasca, High Prairie, Valleyview, Fairview, Peace River, Whitecourt, Mayerthorpe and many more rural areas and towns.

Edmonton Commercial Roof Penetration Install, October 2014

This commercial client reached out to us about having two roof penetrations installed properly on their EPDM roof. The roof was very muddy and needed to be cleaned before the installation could begin. Photos sent by the client showing the roof penetrations: 20140814_102849_resized 20140814_102930_resized Roof Report, October 17th, 2014:
This was an EPDM roof which the client needed two penetrations installed on. The roof was very dirty and covered in mud which took some time to clean. They had used silicone to put a temporary seal which we had to remove once we had cleaned the area. We roofed it in with form flash and the job is now 100% complete. This was an hourly dispatch plus materials.
Materials Used:
  • 24ft. of 12 inch form flash.
  • 1 can of primer.
  • 1 bag of rags.
  • (1) 1 gallon can of splice wash.
  • 2 tubes of lap seal.
20141016_142913_resized 20141016_142922_resized 20141016_142946_resized 20141016_160512_resized 20141016_173518_resized 20141016_173525_resized 20141016_173534_resized 20141016_173542_resized < End Report > CODE: 9503 Contact Us Call our 24 hour emergency roof repair at 1.780.424.7663. Mail to: 3428 99 Street NW Edmonton, Alberta T6E-5X5. We service all of Alberta including Edmonton, Stony Plain, Spruce Grove, Fort Saskatchewan, St Albert, Sherwood Park, Leduc, Nisku, Beaumont, Lac La Biche, Grande Prairie, High Level, Westlock, Slave Lake, Edson, Drayton Valley, Devon, Camrose, Wetaskiwin, Tofield, Lamont, Morinville, Vegreville, Tofield, Millet, Calmar, Evansburg, Redwater, Onaway, Viking, Athabasca, High Prairie, Valleyview, Fairview, Peace River, Whitecourt, Mayerthorpe and many more rural areas and towns.

Edmonton Commercial Roof Inspection Report, July 2014

This commercial client required a full rooftop inspection by one of our red seal journeymen. The report outlines the many issues encountered on the rooftop and includes photos of the site. Inspection, July 4, 2014: This roof is an SBS Modified Torch on replacement and it was observed in a complete failed condition. The numbers of failure areas are so numerous that itemizing each would take many hours - this report will only explain generally what was observed because the whole roof was considered failed. Generally speaking most of the torch side laps were not heated correctly which in itself has caused the roof to fail. End laps and side laps were found at numerous areas to be less than the required measurements (side laps at 3” and connecting rolls at 6”). There were areas observed where the field rolls were installed over flashing which is opposite of procedure. The termination points of SBS at walls where flashing is required is not done, the rolls were not cut at the corners prior to the next roll installed, and drainage was not designed correctly (the slope is not appropriate). There were numerous improperly applied repair patches at seams that were failed. Much of the detail work at the corners of units and penetrations was done incorrectly, and the flashing membrane at the parapets did not extend in many instances fully up the vertical to the top of the parapet and across and terminating at the outside edge. The stripping at the parapet walls was not adhered correctly in many instances, and it did not extend at least 4” over the field. Considering the numerous application issues the roof application is over-all in a failed condition. 20140428_133742_resized_1 20140428_133747_resized_1 20140428_133752_resized_1 20140428_133824_resized_1 20140428_133847_resized_1 20140428_133901_resized_1 20140428_133956_resized_1 20140428_134002_resized_1 20140428_134011_resized_1 20140428_134035_resized_1 20140428_134059_resized 20140428_134129_resized_1 20140428_134135_resized_1 20140428_134144_resized_1 20140428_134149_resized_1 20140428_135406_resized_1 < End Report > CODE: 14225 Contact Us Call our 24 hour emergency roof repair at 1.780.424.7663. Mail to: 3428 99 Street NW Edmonton, Alberta T6E-5X5. We service all of Alberta including Edmonton, Stony Plain, Spruce Grove, Fort Saskatchewan, St Albert, Sherwood Park, Leduc, Nisku, Beaumont, Lac La Biche, Grande Prairie, High Level, Westlock, Slave Lake, Edson, Drayton Valley, Devon, Camrose, Wetaskiwin, Tofield, Lamont, Morinville, Vegreville, Tofield, Millet, Calmar, Evansburg, Redwater, Onaway, Viking, Athabasca, High Prairie, Valleyview, Fairview, Peace River, Whitecourt, Mayerthorpe and many more rural areas and towns.

Edmonton Commercial Roof Downspout Install, March 2014

This client required a downspout replacement and extension in addition to a scupper installation. The report follows the work completed by the GRS crew and includes photos of the site. Roof Report, March 29, 2014:
Today we scoped out the job site with the client. The scope of work will be to install a scupper, replace and extend the downspout, and to top up the pea gravel on several areas of the roof.
Materials Needed:
  • (1) 6x6 scupper.
  • (10) 100' dark brown downspout.
  • 1 box of screws self tap.
  • 1 pail - sopramastic gum/tar.
  • 1 roll - reinforced mesh (jewt).
  • (2)  5 gallon pails of pea gravel.
20140329_08225320140329_08234820140329_08235320140329_082404
Roof Report, April 24, 2014: Today we fixed the down pipe and installed an elbow. When I went to install the scupper box I called our project coordinator and he said it had to be a torch-on tie in. The roof was still wet from the previous rain so we are going to leave this until the roof has dried. I notified the customer of the schedule change due to water on the roof and she was okay with it. 11 image Roof Report, May 8, 2014: We installed one scupper with a torch-on tie on to the BUR roof, and I also had to modify the metal where the scupper was placed. There was an uneven balance to the roof so we put more rock on the places where it was needed. When finished with the scupper I had to fix the down pipe that was connected to it and where the down pipe hits the ground. This site is now complete. 0 1   4 5 6  8 9 < End Report > CODE: 13104 Contact Us Call our 24 hour emergency roofing repair at 1.780.424.7663. Mail to: 3428 99 Street NW Edmonton, Alberta T6E-5X5. We service all of Alberta including Edmonton, Stony Plain, Spruce Grove, Fort Saskatchewan, St Albert, Sherwood Park, Leduc, Nisku, Beaumont, Lac La Biche, Grande Prairie, High Level, Westlock, Slave Lake, Edson, Drayton Valley, Devon, Camrose, Wetaskiwin, Tofield, Lamont, Morinville, Vegreville, Tofield, Millet, Calmar, Evansburg, Redwater, Onaway, Viking, Athabasca, High Prairie, Valleyview, Fairview, Peace River, Whitecourt, Mayerthorpe and many more rural areas and towns.

Edmonton Commercial EPDM Roof Repair, July 2013

This report follows an EPDM repair on a commercial building in Edmonton. The original roof is in rough shape and there are multiple spots where water is leaking into the building. Some of the gravel has also been removed which is causing the tar to degrade underneath. SCOPE OF WORK
Entry, Small Tar/Gravel Roof:
  • Front NW entrance leaking around skylights. Re-seal skylights, restaurant and lobby, tar/gravel roof.
  • Skylight in main lobby (roof blistering across whole roof). Repair all blisters.
Pool Area TPO Roof:
  • Pool area, between skylights (TPO not high enough around power ventilator unit, TPO on wall pulled away 5'9" high up wall). Replace TPO and extend to area.
  • Repair hallway in front of exercise room (main floor).
Tower, EPDM Roof large stone spread 6 floor:
  • Repair two leaks on separate rooms (5th, 6th floor).
  • Repair hall on 6th floor.
  • Repair cracks around roof access hatch.
Inn Side Building area, Tar/gravel roof:
  • Repair leak on 3rd floor on south side of hall.
  • Blistering across whole south side of roof - repair blistering.
  • Heavy blistering around A.C units - repair blistering.
Banquet Side area, Tar/gravel roof sections:
  • Blistering across whole roof surface - repair blistering.
  • Heavy blistering around all units and all parapet walls - repair blistering.
The original state of the rooftop: 1 2 3 4 5 6 7 8 9 10 The crew began on the EPDM repairs by locating all of the issues and cleaning the affected areas. These areas were then patched and caulked. Flex flashing was applied and the field seams were caulked under the clamping ring. Some scraping and spudding was also required in order to apply the plastic cement. At this point there is still some work to be done on the lower TPO section. Materials Used:
  • 6 pails of plastic cement.
  • 8 tubes of cut off.
  • 10 tubes of caulking.
  • Flex flashing.
IMAG0567IMAG0569 IMAG0570 IMAG0571 IMAG0572 IMAG0573 IMAG0574 IMAG0575 IMAG0576 IMAG0577 IMAG0578 IMAG0579 IMAG0580 IMAG0582 IMAG0583 IMAG0584 The crew swept and exposed 3 squares of 4 ply on the third floor. The leaking area was located and plastic cement was applied with cotton. The area with the scupper was also sealed with plastic cement. One of the caps on the front ramp section was caulked, however an inside corner still needs to be sealed properly. 15 areas at the pool section were cleaned and then repaired using plastic cement. In order to fix the leaking skylight plastic cement was placed around the hatch.
Materials Used:
  • 5 pails of plastic cement.
  • 1 role of 6" cotton.
  • 3 tubes of caulking .
The crew spoke with the client at the front desk and he is satisfied with the work done to date. The majority of the leaks have been repaired at this point.
  IMAG0693 IMAG0694 IMAG0695 IMAG0696 IMAG0698 IMAG0699 IMAG0711 IMAG0714 IMAG0717 IMAG0718 IMAG0719
< End Report > CODE: 18035
Contact Us Call our 24 hour emergency roof repair at 1.780.424.7663. Mail to: 3428 99 Street NW Edmonton, Alberta T6E-5X5. We service all of Alberta including Edmonton, Stony Plain, Spruce Grove, Fort Saskatchewan, St Albert, Sherwood Park, Leduc, Nisku, Beaumont, Lac La Biche, Grande Prairie, High Level, Westlock, Slave Lake, Edson, Drayton Valley, Devon, Camrose, Wetaskiwin, Tofield, Lamont, Morinville, Vegreville, Tofield, Millet, Calmar, Evansburg, Redwater, Onaway, Viking, Athabasca, High Prairie, Valleyview, Fairview, Peace River, Whitecourt, Mayerthorpe and many more rural areas and towns.

Edmonton Shingle Estimate and Repair, April 2013

This client was in the process of purchasing a new home which had several missing shingles. A request was made to GRS for an inspection and estimate to replace the missing shingles. Inspection Notes: There are 5 missing 3-tab shingles which need to be replaced, as well as nails to refasten the metal fan vents, and rubber modified bitumen to seal off exposed nails in the anchor points and roof fixtures. If you decide to hire us to fix the roof, we will be able to match the shingle style and colour, and I should be able to repair the roof within the same day as I receive the work order. There is no Ice and Water Shield along the eavestroughs or valleys, but in order to install this the roof would have to be replaced completely. If you have any questions you can respond to this e-mail or please call me on my cell phone. DCIM101GOPRO DCIM101GOPRO DCIM101GOPRO The repairs were made successfully and the client sent the following email expressing her pleasure in our work:
Good morning, Thank you for taking care of the roof repairs so quickly.  When you have a chance can you let me know what all you did and if I need to follow up on anything other than the ice shield. Thanks again.
< End Report > CODE: 15624 Contact Us Call our 24 hour emergency roof repair at 1.780.424.7663. Mail to: 3428 99 Street NW Edmonton, Alberta T6E-5X5. We service all of Alberta including Edmonton, Stony Plain, Spruce Grove, Fort Saskatchewan, St Albert, Sherwood Park, Leduc, Nisku, Beaumont, Lac La Biche, Grande Prairie, High Level, Westlock, Slave Lake, Edson, Drayton Valley, Devon, Camrose, Wetaskiwin, Tofield, Lamont, Morinville, Vegreville, Tofield, Millet, Calmar, Evansburg, Redwater, Onaway, Viking, Athabasca, High Prairie, Valleyview, Fairview, Peace River, Whitecourt, Mayerthorpe and many more rural areas and toeDeDwns.

Edmonton Commercial Roof Leak Inspection, June 2012

This client in Edmonton required a roof inspection due to leaking that was occurring during heavy rainfalls. This brief report outlines the initial inspection and includes photos of the site. Inspection, June 13, 2012: Upon arrival at the site we talked with a manager who directed us to the roof hatch and the damaged office area. We spoke to the person whose desk was directly under the leak, and he noted that the leak only occurred when there was very heavy rain. All vents in the problem area described were inspected. The plastic cement was also inspected and it appeared to be solid. We determined that the large unit in the area was the source of the leak (we calculated it to be directly above the leak area). We scraped the gravel from around the unit and lifted up the flashing in order to get a better look, and to expose the area for the incoming rain. After the rain had passed, we inspected both the unit and the office area. No leaks were found in the office area. We swept the pools of water around the unit onto the unit itself, trying to provoke a leak, but there were still no leaks. This led us to conclude that there were no leaks in the roof, and the leak that occurred previously was due to the rain being so heavy that it must have overflowed into the unit itself; if there was a problem with the roof, then the rain today would have exposed it. IMG_1827 IMG_1828 IMG_1829 IMG_1830 IMG_1831 IMG_1832 IMG_1833 IMG_1834 IMG_1835 IMG_1836 IMG_1837 IMG_1838 IMG_1839 IMG_1840 IMG_1841 IMG_1842 IMG_1843 IMG_1844 IMG_1845 IMG_1846 IMG_1847 IMG_1848 IMG_1849 IMG_1850 IMG_1851 IMG_1852 IMG_1853 IMG_1854 IMG_1855 IMG_1856 IMG_1857 < End Report > CODE: 14520 Contact Us 24 Hour Emergency Roof Repair. Telephone: 1.403.873.7663. Email: info@calgaryroofrepair.ca. Mailing: 240 – 70 Shawville Boulevard SE Calgary, Alberta. T2Y 2Z3. For all other areas of Canada call 1.877.497.3528 Toll Free. We service all areas of southern and central Alberta and south east British Columbia including Airdrie, Banff, Calgary, Canmore, Crossfield, Carstairs, Didsbury, Olds, Sundre, Three Hills, Drumheller, Hanna, Brooks, Bassano, Strathmore, Chestermere, Irricana, Cochrane, Black Diamond, Okotoks, Priddis, Bragg Creek, Cranbrook, Fernie, Panorama, High River, Vulcan, Medicine Hat, Lethbridge, Taber, Sylvan Lake, Red Deer and other Alberta rural points between.