EPDM Roofing Replacement, July and August 2015, Edmonton

Below you will find a series of ongoing reports for a client in Edmonton looking to re-roof their building with an EPDM system. The building is a low slope duplex, where the entire roof would receive treatment with the new surface.
Table of Contents:
September 2 [Service Follow-up]
  Inquiry and Inspection: July 23, 2015 The client first reached out to us in late July to have the roof on their residential building replaced with an EPDM system. After completing the work orders and both sides coming to terms with respect to the work to be carried out, inclement weather put things on hold for some time. In early August, we notified the client that we would deliver the EPDM to their rooftop so that it could be accessed with a moment's notice on fair-weathered days.   Roof Report: August 12, 2015 We arrived on-site to measure the roof and determine what insulation was laid under the current surface. They found the work-space to be 45 ft. x 47 ft., and compiled a list of materials that are expected to be used in the job. Materials:
  • Twelve 4" vents.
  • Four dryer vents.
  • Four gas heat stacks.
  • One scupper.
  • One roof drain.
IMG_20150812_123728
We began the replacement by measuring the roof perimeter and determining what insulation was being used underneath the current surface.
IMG_20150812_123812
Next, we determined what rooftop appliances required replacement and whether there were any new components that needed to be ordered.
IMG_20150812_124540
A section of the roof was cut open to determine what insulation was being used. The roof was insulated using fiberglass wood chips.
IMG_20150812_125346
Finally, we inspected the edges to see whether any new flashing needed to be ordered.
  Roof Report: August 24, 2015 The materials were cleared off the roof and detail work was completed. Waste was brought to the disposal bin, and the bin area was cleaned up and designated ready for pick-up. Upon final review, the roof is completed and can be double-checked next week. The disposal bin service was unable to pick up their bin, so pickup has been scheduled for one day hence, August 25.
20150824_152747
All of the roof ballasting was removed until the surface was exposed. It was cleared to a point where EPDM could be rolled out onto the surface.
20150824_152751
Each run of EPDM was fully-adhered to the roof surface using a bonding agent. After one run was finishing drying, we would move onto the next one.
20150824_152753
To ensure watertightness, we apply liquid rubber coatings over the seams formed between each run of EPDM.
20150824_152805
We had to customize the EPDM to fit around this cluster of rooftop appliances. To waterproof the base of each unit, we used seam tape and liquid rubber coatings.
  Service Followup: September 2, 2015 The job site is now considered complete, and the EPDM roof replacement was done successfully. Below are photos of the finished project, as taken by the roofing team handling the site.
20150901_171021
Post-installation photo of newly fastened edge flashing.
20150901_171010
The roof replacement was wrapped up with a new scupper and drain installation.
    < End Report > CODE: 12743 Contact Us Call our 24 hour emergency roof repair at 1.780.424.7663. Mail to: 3428 99 Street NW Edmonton, Alberta T6E-5X5. We service all of Alberta including Edmonton, Stony Plain, Spruce Grove, Fort Saskatchewan, St Albert, Sherwood Park, Leduc, Nisku, Beaumont, Lac La Biche, Grande Prairie, High Level, Westlock, Slave Lake, Edson, Drayton Valley, Devon, Camrose, Wetaskiwin, Tofield, Lamont, Morinville, Vegreville, Tofield, Millet, Calmar, Evansburg, Redwater, Onaway, Viking, Athabasca, High Prairie, Valleyview, Fairview, Peace River, Whitecourt, Mayerthorpe and many more rural areas and towns.

Leave a Reply