Ongoing Roof Leak Maintenance in Sherwood Park AB, May to July 2015

Assessment, May 7 2015: The site had a plumbing issue; the drain was backed up. Our client said if there were any roofing problems in the future, that they would definitely contact us. Surely enough, we received a call the next month. Scope of Work, June 1 2015: We are to locate and fix the leaks of a BUR roof and add one drain basket to the drain. When we got up to the roof, we had to locate two leaks which were both in the center of the roof but about 15 ft. away from each other. Once we swept all the gravel back, we noticed there had been two large gum patches that were previously installed by another contractor and had now failed. To test for failure, I pushed water out of the areas in the patch. We spudded both areas. One leak was 12 ft. x 1.5 ft. and the second was 10 ft. x 3 ft. Each tapered down to 1 ft. once both areas were spudded. Underneath, there were signs of water saturation, so we had to dry each area with a shop vac. Once dry, we then gave them a coat of asphalt prime to help the MASTIC bond on the BUR system. Once priming was complete, we then applied a coat of MASTIC to the entire system followed by a layer of reinforcement mesh. Another top coat of MASTIC was applied to seal in the mesh.
20150601_104710
We cleared gravel away from sections of the roof that we suspected water was entering through.
20150601_110050
Tears were found in some parts. We used SOPRAMASTIC to seal them in.
20150601_121144
Here is another exposed section which had been a tear running over a significant section of the roof.
20150601_115104
After spudding the tear, we applied mesh over top.
20150601_120319
A second coat of spudding was then applied over the mesh.
20150601_124628
We then let the second layer of spudding dry over the mesh.
Our second scope of work was to install a drain basket. Unfortunately, this could not be accomplished because it had been completely covered with MASTIC. There was nothing to fasten the basket to. Materials:
  • 25 ft. of 3ft. mesh
  • 3x pails of MASTIC roof patch
  • 1x can of spray primer
Followup - Installation Report, June 17 2015: After filling out safety documentation, we met with the client to go over leaks on the main roof when we had performed repairs on during the previous visit. From the client's assessment, there was still apparent leaking. A crew member went up on the roof and searched but could not finding anything. We will need to return when it is leaking actually occurs to get a better idea of where it is coming from. As for the roof above the restaurant, we tracked the leak to an air unit. Once we removed the metal, paper around the base was splitting and water was getting in, evidenced by moisture. We spudded the entire perimeter and applied a coat of MASTIC, followed by a layer of reinforcement mesh, and finally a top coat of MASTIC. We then reinstalled the metal and cleaned up the site.
20150601_104746
Second leak site, with a small tear on an exposed section of the roof.
20150601_105924
Moisture buildup underneath gravel.
20150601_124913
Redistributing gravel over the newly patched area. We followed a similar process as our first visit to address the section with the moisture buildup.
20150601_112813
Second leak site.
20150601_123059
Spudding and mesh being applied over the second leak site.
20150601_124629
Completed spud over the mesh.
Materials:
  • 2x pails of MASTIC
  • 25 ft. of 6 in. mesh
Quotation, June 23 2015:
  • SBS 2-ply patch along entire down-slope (60 ft. x 20 ft. patch)
  • Drain replacement with u-flows
Scope of Work: Remove all gravel in the area, spud out 10 ft. on either side of the drains, and 60 ft. down the low ride of the roof. Roll on asphalt primer and torch down the base. Add new drains with u-flows and cap the entire area. Materials:
  • 9x rolls of cap
  • 9x rolls of base
  • 10x gallons of asphalt primer
  • 2x 4 in. drains
  • 2x 4 in. U-flows
  • 2x pails of MASTIC
The client approved our quotation on the 25th of June:
Please go ahead with this job and let’s hope it solves our leaking issues.
Field Report, July 13 2015: We had our safety meeting and went up to the roof to shovel all the gravel away from the work-site and spudded the segments of interest in preparation of a patch. It started to rain and we had to call it a day.
IMAG0230
Arriving to the site
IMAG0231
We had to dry the area
IMAG0233_BURST002_COVER
Another view of the BUR system
IMAG0252
Entire site spudded
IMAG0255
Side view
IMAG0256
Ventilation system covered
Our crew had to delay work for the next few days due to heavy rain conditions.  July 17 2015: Preparatory work was completed today when we got the patch based in. A skeleton crew was left behind for fire watch. < End Report > More updates from this site will be posted as new field reports become available. Code: 33 Contact Us Call our 24 hour emergency roof repair at 1.780.424.7663. Mail to: 3428 99 Street NW Edmonton, Alberta T6E-5X5. We service all of Alberta including Edmonton, Stony Plain, Spruce Grove, Fort Saskatchewan, St Albert, Sherwood Park, Leduc, Nisku, Beaumont, Lac La Biche, Grande Prairie, High Level, Westlock, Slave Lake, Edson, Drayton Valley, Devon, Camrose, Wetaskiwin, Tofield, Lamont, Morinville, Vegreville, Tofield, Millet, Calmar, Evansburg, Redwater, Onaway, Viking, Athabasca, High Prairie, Valleyview, Fairview, Peace River, Whitecourt, Mayerthorpe and many more rural areas and towns.

Residential Roof Leak Repair in Edmonton AB, July 22 2015

Below you will find an initial assessment for an ongoing residential site by our Edmonton roofing repair crew. More reports will be posted as they become available. Initial Assessment, July 22 2015: We arrived on-site at 1:00 pm and were lead by the client to two leaks in the shop. One was coming from around the skylight, and another one around the chimney stack in the middle near the edge of the roof. Upon inspecting the roof top-side, we observed that the acrylic MASTIC around the chimney was cracking and lifting in areas. It should be removed and replaced with seam tape and liquid rubber. The penetrations require the same. It is only a matter of time until it begins to leak around the entire skylight. There are also cracks and splits in the skylight, which seems to have had been coated with spray foam. The metal gum box also needs to be topped off. There is a metal boot top-side as well that looks like it was only spray foamed. The roof measurements are 85 ft. long by 51 ft. wide, and the skylight was 4 ft. x 4 ft. It should take 25 man hours to clean and repair the penetrations, apply some gum patch into the metal boot, and cover the foam/top up the gum box with rubber MASTIC. < TO BE CONTINUED > Code: 154 Contact Us Call our 24 hour emergency roof repair at 1.780.424.7663. Mail to: 3428 99 Street NW Edmonton, Alberta T6E-5X5. We service all of Alberta including Edmonton, Stony Plain, Spruce Grove, Fort Saskatchewan, St Albert, Sherwood Park, Leduc, Nisku, Beaumont, Lac La Biche, Grande Prairie, High Level, Westlock, Slave Lake, Edson, Drayton Valley, Devon, Camrose, Wetaskiwin, Tofield, Lamont, Morinville, Vegreville, Tofield, Millet, Calmar, Evansburg, Redwater, Onaway, Viking, Athabasca, High Prairie, Valleyview, Fairview, Peace River, Whitecourt, Mayerthorpe and many more rural areas and towns.

Photo Journal: TPO Flat Roof Recovery and Sloped Insulation in High Level, AB

Below you will find a photo journal from a commercial contract in High Level, Alberta. The work entailed a TPO flat roof recovery and sloped insulation. Background When a roof reaches the end of its life, our clients are faced with the choice of either a full replacement or a recovery. Roof recovery refers to applying a new system over an existing one when the roof is reaching its end-of-life (1). Depending on climate conditions, preference, or preexisting solutions, a roof recovery may be performed using TPO, EPDM, bitumen, cap-sheets and/or asphalt. Sloped insulation refers to the tapering that exists on an insulation system. As a weatherproofing measure, when precipitation reaches your roof, it will run off into the drain system down the slope. Call us today for a consult on which roof recovery system is right for your commercial, industrial, or residential environment. < End Journal > Code: HIGH Article Topics: TPO Flat Roof High Level Alberta. Contact Us Call our 24 hour emergency roof repair at 1.780.424.7663. Mail to: 3428 99 Street NW Edmonton, Alberta T6E-5X5. We service all of Alberta including Edmonton, Stony Plain, Spruce Grove, Fort Saskatchewan, St Albert, Sherwood Park, Leduc, Nisku, Beaumont, Lac La Biche, Grande Prairie, High Level, Westlock, Slave Lake, Edson, Drayton Valley, Devon, Camrose, Wetaskiwin, Tofield, Lamont, Morinville, Vegreville, Tofield, Millet, Calmar, Evansburg, Redwater, Onaway, Viking, Athabasca, High Prairie, Valleyview, Fairview, Peace River, Whitecourt, Mayerthorpe and many more rural areas and towns.

Roof Leak Repair in Edmonton AB, December 2014 and July 2015

Below you will find an assessment and field report from the Edmonton roof leak repair crew for a residential client. The roof had been experiencing leaks on two occasions due to a lack of proper ventilation and insulation. Assessment, December 12 2014: By the time we had arrived, the leaking had stopped. However, our client still had buckets out in her kitchen for water collection. The client also showed me the garage, where there appeared to be water damaged on the ceiling. Again, no evident leaking at the time of assessment. A roof inspection was also completed, and we found 4 in. of ice damming.
20141211_140350_resized
Water collection in kitchen
20141211_140354_resized
Interior assessment
20141211_140507_resized
Garage assessment
20141211_141257_resized
Ice damming
20141211_141540_resized
First leak site
20141211_142207_resized
Second leak site
  Installation, July 20 2015: When I arrived on-site, the client showed me two leaks. One was in the living room and another in a bedroom. Both leaks were in line with each other. On the roof, a crack running half the length of the roof was found - the same cracked that was fixed the year before. The crack had probably reoccurred due to a lack of insulation and venting. We fixed the crack again with LR and the client was notified about the insulation and ventilation.
20150718_121643
Crack running the roof length
20150718_121649
Reoccurring crack
20150718_121726
Flooding the area
20150718_123607
LR repair
20150718_123620
LR, post-application
  < End Report > Code: 6407 Contact Us Call our 24 hour emergency roof repair at 1.780.424.7663. Mail to: 3428 99 Street NW Edmonton, Alberta T6E-5X5. We service all of Alberta including Edmonton, Stony Plain, Spruce Grove, Fort Saskatchewan, St Albert, Sherwood Park, Leduc, Nisku, Beaumont, Lac La Biche, Grande Prairie, High Level, Westlock, Slave Lake, Edson, Drayton Valley, Devon, Camrose, Wetaskiwin, Tofield, Lamont, Morinville, Vegreville, Tofield, Millet, Calmar, Evansburg, Redwater, Onaway, Viking, Athabasca, High Prairie, Valleyview, Fairview, Peace River, Whitecourt, Mayerthorpe and many more rural areas and towns.

Edmonton Roof Repair – Weather Forecast Favorable for Re-Roofing

Today's Forecast... Fix Your Roof Leaks. Get Your Edmonton Roof Repair or Re-Roofing Done Now!

Edmonton Roof Repair - Weather Forecast Favorable! The weather in Edmonton lately has had our roof repair crews start and stop and start and top numerous times a day. June is a rain month in Alberta so we should have expected that. Update: 1:50 PM Weather Update. Well, just checked the radar for our roofing crews and there may be a shower around 2:30 this afternoon and there is a high probability of a good rain shower between 7:30 - 9:00 tonight. So important to button up those re-roofs before it rains!
Edmonton Roof Repair - Weather Radar Update 150 PM
Edmonton Roof Repair - Weather Radar Update 150 PM
This morning's radar says it's a favorable day to get those roof repairs done.
Hopefully by the time I click publish to this post and check the radar the rain clouds aren't moving in. According to The Weather Network, the average monthly rainfall in Edmonton is 59 mm and precipitation is 71 mm (I'll have to research what the difference is when I get a moment sometime). I just checked CTV Edmonton website and CTV Edmonton Chief Meteorologist Josh Classen's forecast for the week is perfect for roof repairs. You can follow him on twitter: @joshclassenCTV Below is the radar from Weather Network screen shot up to 2:00 PM today.
Edmonton Roof Repair, Weather
Edmonton Roof Repair - No Rain in Weather Forecast Today
http://www.theweathernetwork.com/weather/canada/alberta/edmonton?wx_auto_reload=forecasts:%20city%20page:%20auto%20refresh So, if you have roof repairs to do it's time to get on them and get your roof leaks fixed. If you need our help call us anytime at 1.780.424.7663. We repair and replace residential, commercial and industrial roofing systems in Edmonton and area. Flat roofs, shingles, tile, cedar, metal and all other roof systems. All the best! Tyler Sinclair   CONTACT US Call our 24 Hour Emergency Roof Repair at 1.780.424.7663. Mail to: 3428 99 Street NW Edmonton, Alberta T6E-5X5. For all other areas of Canada call 1.877.497.3528 Toll Free. We service all of Alberta including Edmonton, Stony Plain, Spruce Grove, Fort Saskatchewan, St Albert, Sherwood Park, Leduc, Nisku, Beaumont, Lac La Biche, Grande Prairie, High Level, Westlock, Slave Lake, Edson, Drayton Valley, Devon, Camrose, Wetaskiwin, Tofield, Lamont, Morinville, Vegreville, Tofield, Millet, Calmar, Evansburg, Redwater, Onaway, Viking, Athabasca, High Prairie, Valleyview, Fairview, Peace River, Whitecourt, Mayerthorpe and many more rural areas and towns.  

Commercial Roof Recovery for Existing Client in Edmonton AB, April to June 2015

Below you will find a series of quotations for an existing commercial client. We had previously dealt with some leaks for them as outlined here. This time, the client required a roof recovery for a 28 ft. x 44 ft. garage. Client files request, April 20 2015:
I know that you quoted on the small garage, we would like another quote that requires the following: layout, retrofit, TPO roof, no asphalt.
Quotation, April 20 2015:
  • Layover, remove stone.
  • Install new 2 in. polyisocyanurate and 0.45 mm TPO membrane.
  • New flashing is required all around to match the front of the building.
Assessment, June 22 2015: We arrived at 8:00 am and searched for roof leaks around the unit for two hours. With no luck, there was still the remaining task of installing the last drain unit over another one of the units which needed work. The roof on the second building is a 28 ft. x 44 ft. BUR roof on a wood deck that leaks in too many places to fix. One drain on the northwest corner and three other penetrations, as well as two vents and a motor exhaust are going through the roof. There is a 4 in. wood detail around the edge and one scupper. We suggest an EPDM roof recovery. The maintenance manager for the site also gave us a call to tell us that a leak was found on the west wall of the building. The crew found numerous rips in the roof along the membrane; it had been completely separated from the drain.

Materials:

  • 5 ft. of cap
  • 5 ft. of base
  • 1x can of spray primer
  • 1x 3 in. drain
  • 1 can of mastic
  • 1x roll of 6 in. reinforcement mesh
New quotation based on assessment, June 22 2015:
  • Gum patches to three or more areas
  • Replace the drain with a new 3 in. unit
  • Roof replacement using an SBS 2 ply system
  • Estimated time: 20 hours
< End Report > Code: 128 Contact Us Call our 24 hour emergency roof repair at 1.780.424.7663. Mail to: 3428 99 Street NW Edmonton, Alberta T6E-5X5. We service all of Alberta including Edmonton, Stony Plain, Spruce Grove, Fort Saskatchewan, St Albert, Sherwood Park, Leduc, Nisku, Beaumont, Lac La Biche, Grande Prairie, High Level, Westlock, Slave Lake, Edson, Drayton Valley, Devon, Camrose, Wetaskiwin, Tofield, Lamont, Morinville, Vegreville, Tofield, Millet, Calmar, Evansburg, Redwater, Onaway, Viking, Athabasca, High Prairie, Valleyview, Fairview, Peace River, Whitecourt, Mayerthorpe and many more rural areas and towns.

High River SBS Roof Replacement, October 2014

This commercial client required a roof replacement and elected to have GRS install a 2-ply SBS Modified Bitumen system. This was done in High River, AB, far to the north of the province.   Roof Report: October 24, 2014 The team arrived on site for 9am and began to get it prepared to commence work the following day. Material lists were organized and ready for purchase, and the tools were loaded onto the roof. The crew waited for the dump bin to arrive, and once it had they went off to the store to pick up the last of the materials needed for the job's beginning. They ended the day for 3:00pm, leaving the job site for the evening.   Roof Report: October 26, 2011 The four team members arrived for 8:00am and worked for a few short hours until 11:30. In their time on site, they stripped off the torch-on system and moved materials to the side of the roof where they would begin work the following day. The weather forecast called for heavy snow, and ice crystals were building on the roof even after torching. They called it for the day at 11:30am, and would return the following morning.   Roof Report: October 29, 2015 Starting the morning at 7:30, the team got to work with chipping away ice, blow-drying the roof, and cleaning it off for work. Once done, they got to stripping outer walls, putting up around 25' of fascia, and stripping the parapet walls too. They installed two high domes and starting putting more capping on. Heavy snowfall came in just before 5:00pm, so the team wrapped up the site for the day.   Updated Quotation Delivered: October 30, 2014 We sent over an updated quote to the client to show payments that had been applied to date. There was some uncertainty remaining about the amount of sheathing requiring replacement, so the final quote was yet to be confirmed.   Roof Report: October 30, 2014 This day saw a lot of ice chipped away and snow swept off of the roof. They team torched the capping and installed scupper drains and the necessary downpipes. They left the job site for 4:00pm once word arrived that some more of the materials for the job site on order had arrived. They got the materials and returned to the town; an 8-hour round trip. Roof Report: October 31, 2014 There was some light rain in the morning, but not enough to cancel the day's progress. The rest of the roof system was ripped off and the rotten plywood underneath replaced. The last scupper drain was installed, and some more of the parapet wall was stripped. Once done, the last of the capping was torched on and materials were moved and prepared for the next day. After clean-up, the team departed the site for around 5:30pm. The day's efforts saw 25 sheets of OSB plywood 7/16 installed, which allowed for a final quote to be delivered to the client as everything that would be exposed and inspected had been so. High Level-20141031-03223 High Level-20141025-03127       Roof Report: November 2, 2014 This day, the team met on the roof for 8:00am and got to work. Their task for the day was working on getting the enco new paper was completed, and the job site was cleaned up afterwards. They left the site at 1:00pm, another job completed.     CODE: 10006 Contact Us Call our 24 hour emergency roof repair at 1.780.424.7663. Mail to: 3428 99 Street NW Edmonton, Alberta T6E-5X5. We service all of Alberta including Edmonton, Stony Plain, Spruce Grove, Fort Saskatchewan, St Albert, Sherwood Park, Leduc, Nisku, Beaumont, Lac La Biche, Grande Prairie, High Level, Westlock, Slave Lake, Edson, Drayton Valley, Devon, Camrose, Wetaskiwin, Tofield, Lamont, Morinville, Vegreville, Tofield, Millet, Calmar, Evansburg, Redwater, Onaway, Viking, Athabasca, High Prairie, Valleyview, Fairview, Peace River, Whitecourt, Mayerthorpe and many more rural areas and towns.

Engineered Liquid Rubber Metal Roof Recovery Ponoka Alberta, May 2014

Below you will find a series of reports from scope of work to completion for a large industrial metal roofing coating project. The Ponoka roofing repair crew provided the following assessment: Scope of Work, May 12 2014: The metal roof will be completed using two-ply engineered liquid rubber recovery. A pressure wash will be used to cleaning, water testing, and for site assessment. Test and replace fasteners as required to complete roof deck, penetrations, and gutters. We will provide sheet metal repair and penetration saddle fabrication as required, as well as remove old caulking. All:
  • Penetrations
  • Roof-to-wall connections
  • Fasteners
  • Ridge, horizontal sheet seams
  • Hidden gutters, and roof edging at external gutters
will be hand-troweled using mesh and high grade rubber as required. Liquid rubber coating will then be applied, allowing a cure time, followed by a repeated hand trowel process as above. This will be followed by a second coat of liquid rubber. The project manager provided a rationale for using engineered coating as well. Although the industrial standard would have been to recommend reflective elastomeric coating or SPF spray foam, they do not have longevity in a Western Canadian climate. Liquid rubber, on the other hand, has been shown to have a 1200% expansion and contraction rate. The idea was to get the "most mileage" out of the metal roofing, which have a high maintenance turnover due to leaks caused by expansion and contraction of the metal. Expenses also increase with wear and tear caused by corrosion. Using high end engineered liquid rubber polymer in this climate and context would skirt many of these ongoing maintenance problems.
Preparation was dirtier than expected
Preparation was dirtier than expected
Old caulking to be removed
Old caulking to be removed
Contract is approved and work begins, June 22 2014:
Before caulking removal
Before caulking removal
After caulking removal
After caulking removal
The Ponoka roof repair crew arrived on-site and completed work on all seams, corners, and details with mesh and liquid rubber, as detailed. A first coat of trowel and liquid rubber brush-grade was applied.
20140621_122017_resized
Initial coating
20140621_121949_resized
Coating around ventilation systems
20140621_145807_resized
Flat metal roofing coats
  Roof completed, June 23 2014: Gutter seams completed using mesh, second rubber layer coated onto the roof.
Rolling liquid rubber
Rolling liquid rubber
Making progress
Making progress
Finished product
Finished product
< End Report > Code: PON Contact Us Call our 24 hour emergency roof repair at 1.780.424.7663. Mail to: 3428 99 Street NW Edmonton, Alberta T6E-5X5. We service all of Alberta including Edmonton, Stony Plain, Spruce Grove, Fort Saskatchewan, St Albert, Sherwood Park, Leduc, Nisku, Beaumont, Lac La Biche, Grande Prairie, High Level, Westlock, Slave Lake, Edson, Drayton Valley, Devon, Camrose, Wetaskiwin, Tofield, Lamont, Morinville, Vegreville, Tofield, Millet, Calmar, Evansburg, Redwater, Onaway, Viking, Athabasca, High Prairie, Valleyview, Fairview, Peace River, Whitecourt, Mayerthorpe and many more rural areas and towns.

Emergency Roof Leak Call in Edmonton AB

Below you will find a series of field reports, quotations, and photo journals for a large industrial client in Edmonton, Alberta. Our roofing repair crew initially responded to a call for roof maintenance. Over the next two years, various sectors of the site would require complete roof replacement, gutter installations, fixture repairs, and ongoing leak maintenance.  Quotation, May 9 2012:
  • Engineered liquid rubber roof coating: 2-ply coat to complete roof, fastener replacement as required, sheet metal repair as required to achieve a water-tight state.
This product is the first product we have had as roofers that solves metal roof issues and has been extremely successful with considerable and complicated roof systems for a number of our Fortune 500 or multi-national clients.
June 13 2012: We stopped by the shop en route to pick up a trowel, caulking, and wet dry gum (plastic cement) in case the leak was able to be fixed immediately upon inspection. On-site, the client lead us to the leak site where tiles were becoming stained. Visible sagging was noted. After removing the stained ceiling tile, it appeared that the leak was coming in around the RTU unit directly above someone's desk in the southwest corner of the top floor. Upon roof inspection, it was clear to me that the problem area was the plumbing vent in-between the exhaust fan and the RTU unit. It had previously been patched with plastic cement as a temporary solution. There are also a few other areas which could potentially leak in the future; a few gas line penetrations, gum cups around guy wire penetrations for antennae on the roof, and a few flashing issues around exhaust fans. IMG_1827 IMG_1828 IMG_1829 IMG_1830 IMG_1831 IMG_1832 IMG_1833 IMG_1834 IMG_1835 IMG_1836 IMG_1837 IMG_1838 IMG_1839 IMG_1840 IMG_1841 IMG_1842 IMG_1843 IMG_1844 IMG_1845 IMG_1846 IMG_1847 IMG_1848 IMG_1849 IMG_1850 IMG_1851 IMG_1853 IMG_1854 IMG_1855 IMG_1856 IMG_1857 Quotation, June 27 2013:
  • Gutter replacement: supply and install industrial fabricated gutter system to the entire building
Quotation, August 2 2012:
  • Roof repair and maintenance overhaul: remove gravel, wash, repair, return gravel
  • Complete roof replacement options: Spray foam (SPF), EPDM, 2-ply SBS modified bitumen (torch-on), 4-ply engineered liquid rubber roof, TOUGH ROOF
  • Roof recovery options: Spray foam (SPF), 2-ply SBS modified bitumen (torch-on), 1-ply coat tar, 2-ply engineered liquid rubber
Field Observations On this tar and gravel roof, piles are exposed and deteriorating; there are soft spots throughout the roof. There are multiple buckles and blisters. Previous contractors have attempted to stop the leak by caulking and using tar, but this is not working. The roof also has several areas where there is no gravel and has severe damage. The vents and flashing need to be resealed. The exposed bitumen in one area has severe lap splitting. I recommend that the roof be replaced or a recovery system be installed. In the event of a recovery, some areas may require replacement of insulation. The roof is approximately 35 years old and mostly like past the point of repairs. -insert sat photos- Work commenced at this site on August 23 2013 due to rainstorms. Field Report, August 23 2012: Gravel was shoveled away to clear a 40 ft. square, where one leak was found in the roof membrane. The origin was traced to another 10 ft. segment, which was torn up. After removing the old membrane, 2-ply flam flam and cap was torched down. The edges of this fixture were gummed to ensure water tightness. All the metal was then removed from units which contained it and inspected for leaks. It was reinstalled after finding no leaks underneath. Afterwards, six gum boxes were filled and the gravel which had been swept away from the problem area was replaced. IMG_3875 IMG_7136 IMG_7167 IMG_7845 IMG_9253   Flat Roof Scope, September 12 2013: The client has approved a 2-ply torch-on roof recovery. We will cut out wet spots. Metal capping has to be saved, as the client does not want to pay for brand new capping. We will not be providing cranes for this site, use jack units if you have to. The metal roof will also need a liquid rubber application. Materials
  • 24x 205 L drums of MetalSafe B-300
  • 24x 18.9 L pails of MetalSafe S-300
  • 15x 18.9 L pails of TrowelGrade B-400
September 19 2013: After making a supply run, we arrived to the site at 2:00 pm. The existing gutter system was measured and called in to get a price quotation for new gutters. September 23 2013: We finished tearing off the existing system and kept torching cap sheet on. A propane refill will be required soon (2x 50 lb. tanks). A bin was also dropped off on-site for waste removal. September 26 2013: Cap metal was measured for the flat roof and we sent in an order for materials. Overhanging cap sheeting was also cut back to a proper size. Liquid rubber preparation work has also begun. Once metal fabrication is completed, we will begin gutter replacement. October 9 2013: New hires were tasked with adding polyurethane to the window sidings and complete roof sheeting. A large part of the morning was spent troubleshooting the liquid rubber machine, but we managed to finish application before the day was finished. We scheduled gutter installation with the client in December. Materials:
  • 4x rolls of SBS cap
  • 4x tubes of SOPRAMASTIC, caulking-style
  • 2x caulking guns
December 10 2013: Assessment before gutter installation - yimg-1108810272-101-1470536555 yimg-1109027976-101-113628373 yimg-1109027976-101--1753848245 yimg-1109059328-101-568203035 December 11 2013: We set a new hire on building gutter end caps. It was a bit slow going since this was his first time doing so with gutters. Two other crew members installed gutter hangers. In the afternoon, the newly built gutter caps and one downpipe were installed. 20131211_163333 20131211_163342 20131211_163355 20131211_163409 20131211_164503   December 13 2013: A large section was ice was removed to install a piece of industrial guttering with attached end caps. We then added hangers and fixed some deficiencies that arose with previously installed gutters and hangars. Two more crew members arrived a couple of hours later and installed gutter downspouts. While they were at it, problematic gutter attachments were dealt with. By the end of the day, all hangars and end caps were completed. Four downspouts remain as well as a small gutter section at the entrance which requires an assessment. 20131213_152531 20131213_152536 20131213_152540 20131213_155034 yimg-1109407680-101-685963814 yimg-1109407680-101--1584029527 December 18 2013: image (1) image (2) image (3) image (4) image (5) image (6) image (7) image (8) image (9) image (10) image (11) image (12) image (13) image December 19 2013: 20131219_092739 20131219_092756 20131219_092806 20131219_092835 20131219_092842 20131219_092847 20131219_092909 20131219_093002 20131219_093546 20131219_093553 20131219_093612 20131219_094323 20131219_094905 20131219_095148 20131219_095155 20131219_095830 20131219_095900 20131219_100031 20131219_100641 20131219_100647 January 2 2014: We were called back for another gutter inspection. Most of the seams are leaking in from the west side of the building and east of the client's main office. The gutter installation job was done in very cold weather, which could be the reason for the leaks. The caulking was probably not well applied. We should review all of the seams for further leaks. 20140102_161544 20140102_161620 20140102_161743 20140102_161750  20140102_161816  20140102_161851  20140102_162058 20140102_161544 20140102_161620  20140102_161750    20140102_161851 20140102_161914 20140102_162058 20140102_162525 20140102_162601 20140102_162616 20140102_162659 20140102_162715 20140102_162739 20140102_162809 20140102_162827 20140102_162849  20140102_162916 20140102_162935  20140102_174714 January 21 2014: Firstly, all ice was removed around the affected unit. Detail patches were torched onto the unit corner, and we re-gummed a gum box. There was a piece of cap that was torched a quarter of the way; the rest had peeled off the affected unit. We dried the peeling and torched it back into place. This was probably the main cause of the office leak. Afterwards, five more soft gum boxes were touched up. A skeleton crew was left behind for firewatch at the end of the day.   20140121_093936 20140121_105608 20140121_122326 20140121_125637 20140121_130513 20140121_135350 20140121_135358 20140121_135411 20140121_135810 20140121_135821 20140121_135834 20140121_155128   < End Report > Code: 130 Contact Us Call our 24 hour emergency roof repair at 1.780.424.7663. Mail to: 3428 99 Street NW Edmonton, Alberta T6E-5X5. We service all of Alberta including Edmonton, Stony Plain, Spruce Grove, Fort Saskatchewan, St Albert, Sherwood Park, Leduc, Nisku, Beaumont, Lac La Biche, Grande Prairie, High Level, Westlock, Slave Lake, Edson, Drayton Valley, Devon, Camrose, Wetaskiwin, Tofield, Lamont, Morinville, Vegreville, Tofield, Millet, Calmar, Evansburg, Redwater, Onaway, Viking, Athabasca, High Prairie, Valleyview, Fairview, Peace River, Whitecourt, Mayerthorpe and many more rural areas and towns.

Edmonton Residential Roof Snow Removal, January 2014

The following report covers the field report and correspondence between GRS and one of our clients in need of roof snow removal on their home's pitched roof. Inquiry Received, January 7 2014: The client called in to GRS' office seeking snow removal service on their pitched shingle roof. Given the urgency and small scope of the services to be tendered, we bypassed the requirement for formal work order submission and provided a quote over email to be approved. The client agreed to the costs associated with snow removal and consented to the crew arriving the following morning. Field Report, January 8 2014: Our crew arrived on-site for 7:45am and spoke with the client, advising that the size of the roof would likely leave the duration of the service call just under two hours to remove the snow and ice dams. The team set up the ladder and cleaned off the whole roof, then returned to ground level to shovel the walkway where snow had landed from the first part of the job. The team left the job around 9:30am; photos of the service appear below. 20140108_081155 20140108_091022 20140108_091040 20140108_091101 < End Report > CODE: 10148 Contact Us Call our 24 hour emergency roof repair at 1.780.424.7663. Mail to: 3428 99 Street NW Edmonton, Alberta T6E-5X5. We service all of Alberta including Edmonton, Stony Plain, Spruce Grove, Fort Saskatchewan, St Albert, Sherwood Park, Leduc, Nisku, Beaumont, Lac La Biche, Grande Prairie, High Level, Westlock, Slave Lake, Edson, Drayton Valley, Devon, Camrose, Wetaskiwin, Tofield, Lamont, Morinville, Vegreville, Tofield, Millet, Calmar, Evansburg, Redwater, Onaway, Viking, Athabasca, High Prairie, Valleyview, Fairview, Peace River, Whitecourt, Mayerthorpe and many more rural areas and towns.