Roof Leak Repair in Edmonton AB, December 2014 and July 2015

Below you will find an assessment and field report from the Edmonton roof leak repair crew for a residential client. The roof had been experiencing leaks on two occasions due to a lack of proper ventilation and insulation. Assessment, December 12 2014: By the time we had arrived, the leaking had stopped. However, our client still had buckets out in her kitchen for water collection. The client also showed me the garage, where there appeared to be water damaged on the ceiling. Again, no evident leaking at the time of assessment. A roof inspection was also completed, and we found 4 in. of ice damming.
20141211_140350_resized
Water collection in kitchen
20141211_140354_resized
Interior assessment
20141211_140507_resized
Garage assessment
20141211_141257_resized
Ice damming
20141211_141540_resized
First leak site
20141211_142207_resized
Second leak site
  Installation, July 20 2015: When I arrived on-site, the client showed me two leaks. One was in the living room and another in a bedroom. Both leaks were in line with each other. On the roof, a crack running half the length of the roof was found - the same cracked that was fixed the year before. The crack had probably reoccurred due to a lack of insulation and venting. We fixed the crack again with LR and the client was notified about the insulation and ventilation.
20150718_121643
Crack running the roof length
20150718_121649
Reoccurring crack
20150718_121726
Flooding the area
20150718_123607
LR repair
20150718_123620
LR, post-application
  < End Report > Code: 6407 Contact Us Call our 24 hour emergency roof repair at 1.780.424.7663. Mail to: 3428 99 Street NW Edmonton, Alberta T6E-5X5. We service all of Alberta including Edmonton, Stony Plain, Spruce Grove, Fort Saskatchewan, St Albert, Sherwood Park, Leduc, Nisku, Beaumont, Lac La Biche, Grande Prairie, High Level, Westlock, Slave Lake, Edson, Drayton Valley, Devon, Camrose, Wetaskiwin, Tofield, Lamont, Morinville, Vegreville, Tofield, Millet, Calmar, Evansburg, Redwater, Onaway, Viking, Athabasca, High Prairie, Valleyview, Fairview, Peace River, Whitecourt, Mayerthorpe and many more rural areas and towns.

Residential Flat Roof Repair Edmonton, June 9 2015

Article: Residential Flat Roof Repair Edmonton, Alberta. EPDM Low Slope Roof Membrane.

Repair of an EPDM low slope roof on a residential home in Edmonton, Alberta. The low slope (flat) roof transitions to a pitched shingle roof. Penetrations and challenges include chimney, skylights, vents, drainage, ice damming, and insulating value on low slope. Additionally the transition between the low and steep roof systems posed challenges. Also a section on choosing the correct low slope membrane and roof assembly.
This customer had originally called us when Edmonton had set records for snow-fall in January of 2012. She had significant snow loads on her roof and the concern was that her roof may collapse. So we removed the snow from her roof and discovered significant ice damming challenges on the low slope portion.
We returned in 2013 and 2014 to do regular roof snow removal because every-time the snow built up on the roof the heat from inside her home would get to the underside of the low slope roof sheathing and cause ice damming. The ice dams would then get in between the laps of the existing roof membrane and result in leaks.
Mid 2014 she contacted us to quote on the replacement of the low slope roofing with hopes of solving the problem.
We quoted the various options for low slope roofing membranes, which included; Spray Foam (SPF), Tar and Gravel, SBS Torch-On, EPDM, TPO, PVC and Liquid Rubber.
Our standard quotations include pricing for the different options available for flat roof system membranes, a roof inspection report, a write-up on the pro's and con's of each type of system and our recommendations for your most suitable roof membrane choices.
Below is a sample flat roof quotation. The first link is a PDF download and the second is a Word Doc file download.
Our customer chose to replace her failing tar and gravel built up roof with an EPDM single ply membrane roof recovery (or retro-fit). This means that we removed the gravel and skinned the bitumen membrane off and then mechanically fastened a roof board and then fully adhered the EPDM. We also did some drain work and scupper work. Our customer did not opt for a complete removal, re-sloping with an engineered slope insulation system, or any additional R value added which could also have been done with simple rigid type insulation boards.
In early 2015 our customer had called with leaks to the low slope membrane - the ice dams were back. This is an important lesson in choosing the correct roof membrane, insulation, drainage, re-sloping and more. Had we been able to re-slope the roof and been able to add insulation value, the heat from the inside of the home would not escape and get to the underside of the roof membrane and cause ice damming. But, the customer requested the least expensive options and even though our reports (see link above for sample quotation and inspection report) explain in detail most considerations, this is the way it was requested to be done by the customer.
So this spring we returned to find the same ice damming causing issues with a now new membrane. We also found drainage issues which were expected - the roof was ponding because a re-slope was not in our scope. And there were some technical (debatable) installation tweaks that may or may not have been required. Nonetheless, we now had a new roof leaking the year after it was installed.
So of course we once again suggested the upgrade options to alleviate the issue but the customer would have nothing with that and requested we simply do the repairs and move on.
Below is an account from the crew of the type of repairs they did to try and mitigate any issues in the future (full well knowing that the prime aggravating factors are insulation value and sloping).
May 5, 2015: Crew Attends to Residential Flat Roof Repair.  We arrived on site at 9:58. We started the day with the toolbox meeting and safety documents. We then went up on roof to determine an installation plan. The scope of work we decided on and did is as follows.
Scope of Work # 1 The first step was to pull all EPDM down to flat roof from under the shingles at the bottom of the sloped roof. This reinstall was to ensure no water could be coming from the flat roof to steep pitch roof transition. We then had to remove all metal flashing from around the two skylights and chimney on the roof. Once we had all the EPDM pulled we started lifting shingles along the first few rows of the sloped roof and applied the EPDM bonding adhesive. This was done under the first couple layers of shingles and to the underside of the EPDM. We then installed the EPDM back under the shingles. Then next step was to apply a bead of water block on the edge of the EPDM under the shingles. Once that was complete we secured EPDM by screwing a piece of turn-bar down on the edge of the EPDM where the water block bead was applied.
Scope of Work # 2 The crew arrived on site at 1 pm and started working on the cricket behind the chimney.  He started by cutting a piece of EPDM 7'x3'. He then had to take the Epdm bonding adhesive and apply in the same manner as the work in scope # 1 by applying the adhesive under the shingles as well as the under side of the Epdm. Once the 7'x3' piece was installed he started working on the corners. Using quick prime and seam tape he seamed in the corners of the Epdm around the chimney.
 
WORK LEFT TO DO: -patch corners -more turn bar and water block -install and or replace shingles Roughly 6 hours of work left to complete.
MATERIALS USED: -7'x3' piece of EPDM -EPDM bonding adhesive 1/3 of a pail -screws -30 ' of termination bar - 2 tubes of water block -tube of caulking for skylights -half a tube of lap sealer for temporary seals -6 feet of seam tape - quick prime 1/8th of a pail.
Residential Flat Roof Repair Edmonton. Pulling EPDM out from under shingles.
Residential Flat Roof Repair Edmonton. Pulling EPDM out from under shingles.
Peeling back Epdm membrane from skylight curbs.
Peeling back Epdm membrane from skylight curbs.
Taking flashing off chimney
Taking flashing off chimney.
Applied EPDM Adhesive
Applied EPDM Adhesive.
Rolling EPDM back under shingles after adhesive was applied.
Rolling EPDM back under shingles after adhesive was applied.
Installed Piece of Termination bar on tup edge of EPDM (under shingles)
Installed Piece of Termination bar on top edge of EPDM (under shingles).
joining two seams of EPDM, with quick prime and seam tape
Joining two seams of EPDM, with quick prime and seam tape.
May 8, 2015: Residential Flat Roof Repair Crew Attends.
We started at 7:30 AM with a daily tool box meeting. We then got up on the roof and started shoveling snow away from work area so we could complete today's scope of work.
Scope #1. Scope one consisted of applying corner patches to the rear corners of the chimney. The next step was to apply tape primer to the EPDM surface on the corner of the chimney. We then cut 6"×6" squares of 6" covers strip  to use at the corner patch.  We applied  this piece on top of the tape primer and let it sit to cure.
Scope #2. Install termination bar for the EPDM on the front of the skylights. For this we measured and cut a piece of turn bar to fit the front side of the sky light. We then screwed (mechanically fastened) the termination bar.
Scope #3. We had to take the bottom two layers of shingles off and replace with new ones. For this we had to carefully lift the bottom rows of shingles and pry out the nails so the shingles would slide out. We then took the new shingles and installed them. This consisted of laying down the first layer and nailing in place. The next step was to put on the second row of shingles which slid under the old existing one and nailed in place half way down the first shingle we layer down. Job is complete.
Completion photo #1 of where shingles at steep pitch meet low slope EPDM membrane.
Completion photo #1 of where shingles at steep pitch meet low slope EPDM membrane.
completion photo #2
Completion photo #2.
Materials Used:
-2 bundles of shingles
-roofing nails
-8'of turn bar
-2' of cover strip
-rags
- tape primer
-screws

< End of report >

Click here to visit our local roof repair website and order a quotation for flat roof repair in Edmonton or area or contact us per below.

CONTACT US
Call our 24 Hour Emergency Roof Repair at 1.780.424.7663. Mail to: 3428 99 Street NW Edmonton, Alberta T6E-5X5.
For all other areas of Canada call 1.877.497.3528 Toll Free.
We service all of Alberta including Edmonton, Stony Plain, Spruce Grove, Fort Saskatchewan, St Albert, Sherwood Park, Leduc, Nisku, Beaumont, Lac La Biche, Grande Prairie, High Level, Westlock, Slave Lake, Edson, Drayton Valley, Devon, Camrose, Wetaskiwin, Tofield, Lamont, Morinville, Vegreville, Tofield, Millet, Calmar, Evansburg, Redwater, Onaway, Viking, Athabasca, High Prairie, Valleyview, Fairview, Peace River, Whitecourt, Mayerthorpe and many more rural areas and towns.
  Code: 10007

Pitched Roof Snow Removal, January 2014, Edmonton

This client required snow removal on their pitched roof, and called GRS to carry out the service. We'd dealt with this client some years prior when we delivered a quotation for roof recovery or replacement options (outlined below), and were happy to assist them once again. Continue reading Pitched Roof Snow Removal, January 2014, Edmonton

Edmonton Residential Roof Snow Removal, January 2014

The following report covers the field report and correspondence between GRS and one of our clients in need of roof snow removal on their home's pitched roof. Inquiry Received, January 7 2014: The client called in to GRS' office seeking snow removal service on their pitched shingle roof. Given the urgency and small scope of the services to be tendered, we bypassed the requirement for formal work order submission and provided a quote over email to be approved. The client agreed to the costs associated with snow removal and consented to the crew arriving the following morning. Field Report, January 8 2014: Our crew arrived on-site for 7:45am and spoke with the client, advising that the size of the roof would likely leave the duration of the service call just under two hours to remove the snow and ice dams. The team set up the ladder and cleaned off the whole roof, then returned to ground level to shovel the walkway where snow had landed from the first part of the job. The team left the job around 9:30am; photos of the service appear below. 20140108_081155 20140108_091022 20140108_091040 20140108_091101 < End Report > CODE: 10148 Contact Us Call our 24 hour emergency roof repair at 1.780.424.7663. Mail to: 3428 99 Street NW Edmonton, Alberta T6E-5X5. We service all of Alberta including Edmonton, Stony Plain, Spruce Grove, Fort Saskatchewan, St Albert, Sherwood Park, Leduc, Nisku, Beaumont, Lac La Biche, Grande Prairie, High Level, Westlock, Slave Lake, Edson, Drayton Valley, Devon, Camrose, Wetaskiwin, Tofield, Lamont, Morinville, Vegreville, Tofield, Millet, Calmar, Evansburg, Redwater, Onaway, Viking, Athabasca, High Prairie, Valleyview, Fairview, Peace River, Whitecourt, Mayerthorpe and many more rural areas and towns.

Ardrossan Shingle Re-Roofing

This client sought GRS' assistance in re-roofing their shingled home. Given the time of year and some company of theirs planned for early December, negotiations took their time and GRS worked through the service in the spring following a troublesome winter. Continue reading Ardrossan Shingle Re-Roofing

Edmonton Leak Inspection, December 2013

This report covers a leak inspection and repair carried out by GRS to one of our commercial client's metal roof system. We had to look through insulation and drain away some collected water from the ceiling. Inspection: December 21, 2013 We isolated the leaks to the southwest (about 20') and east (40' - 50') corners of the upper roof near the gutter systems. There was ice and snow buildup that had to be cleared away before a rooftop investigation could continue, so it was dealt with and we confirmed some potential areas for water ingress. The team also removed insulation from the ceiling one piece of plywood from the wall to inspect the area underneath the gutters. Findings: There was a great deal of moisture on the back of metal roof panels (that even poured out a bit when insulation was removed. The standing seam was wet to the touch (on the interior) and nearly dripping. This was likely caused by the amount of ice overfilling the gutter by 2" or more. There is also a possibility that the downpipe and gutter connection is leaking. In cases such as this, it could be that water freezes in the pipe, creeps over the connection, and seeps into the walls when it thaws out. Both of the leaks reported seem to stem from the same cause, which leaves us hopeful that repairs can be made to one location and prevent the problems in two. We advised the client of these possibilities, but informed them that there may be a few attempts made over the course of the season, considering the existing ice makes for difficulties in the repair attempts. For the time being, snow can be removed from the building's roof and EDM applied to the potential problem sites as a temporary fix to tide the client over until warmer weather arrives. image-1 image image-13 image-12 image-11 image-10 image-9 image-8 image-7 image-6 image-5 image-4 image-3 image-2 < End Report > CODE: 5611 Contact Us Call our 24 hour emergency roof repair at 1.780.424.7663. Mail to: 3428 99 Street NW Edmonton, Alberta T6E-5X5. We service all of Alberta including Edmonton, Stony Plain, Spruce Grove, Fort Saskatchewan, St Albert, Sherwood Park, Leduc, Nisku, Beaumont, Lac La Biche, Grande Prairie, High Level, Westlock, Slave Lake, Edson, Drayton Valley, Devon, Camrose, Wetaskiwin, Tofield, Lamont, Morinville, Vegreville, Tofield, Millet, Calmar, Evansburg, Redwater, Onaway, Viking, Athabasca, High Prairie, Valleyview, Fairview, Peace River, Whitecourt, Mayerthorpe and many more rural areas and towns.    

Tile Roof Inspection, April 2013, Edmonton

This client reached out to GRS for work on their multi-home building's roof. It is a tile system, with several reports of water ingress and expected damage to the roof itself. GRS sent out a technician to investigate the problems. Unfortunately, photos of the roof taken during inspection are no longer available. The placeholder image above simply provides context to the roofing system style.   Quotation Delivered: April 3, 2013 GRS delivered a quotation to the client covering the services they'd requested. The scope of the work, as outlined in the document, was to remove the tile, check the underlying membrane and valleys, carry out any repairs, then reset the tile system back on top. Before scheduling the work, however, we felt that it would be best to send an inspector out to investigate the problem areas to ensure that the quotation would be fair to both parties in the arrangement.   Inspection: April 22, 2013 The inspection crew went on-site to examine the extent of reported damages. For four of the suites in the building, they checked the roof above and found some major damages that required repair. Near the first suite, there was a major hole in the firewall where both sides of the lead wall's flashing were bent and folded back. The extent of the damage was allowing water to run in behind the flashing and through the hole, spreading down to the suites below as far as the first floor. There was also a piece of wall flashing missing on the front of the turret in the same section, with potential leaks on either side of the chimney in the area. The chimney itself was missing a proper installation and application of ice and water membrane/shield installed around it. Across from these affected areas, on the back of the building, there were several cracked and/or missing tiles in the valley, exposing the roof deck to water and snow that had allowed water ingress to the suite below. In this section of the roof, all of the tiles would need to be removed and the ice and water membrane installed underneath so as to prevent further leaking. Then, with the tiles put back in place, the missing/cracked ones will need to be outright replaced with new ones. Above yet another unit (on the northern corner of the building) there is a long valley that might be overflowing its metal flashing sidewalls and into the attic. Above this valley is a set of short, attaching valleys that separate at 6/12 grade roof from a 4/12; creating a 2/12 grade roof in the middle. On this last 2/12 roof section a great deal of snow could/would pile up during the winter, creating ice dams that allow for a backup of water. These problematic valleys should have the ice shield material on either side of the metal to help keep water in the valley itself. When the crew first attended the site to investigate problem areas and leaks, there were only three that they knew to be coming in. While atop the roof, however, they found that there was no ice and water membrane used alongside any of the roof valleys (not just the ones noted above). Given their absence, it's possible that any and all of the valleys could become future candidates for leaks or further roof damages, especially when any of the surrounding tiles are cracked or otherwise broken/misplaced. The investigative team advised that the roof be cleaned off of leaves and debris, which would allow for a thorough accounting of all of the tiles and the existing system. Rubber-modified sopramastic should be applied to all cracked tiles around the roof to prevent further leakage, and the side cap tiles should be refastened in any places where the nails seem loose or missing.   This post will be updated with roof reports should the client elect to contract GRS to carry out the required work.   CODE: 6703 Contact Us Call our 24 hour emergency roof repair at 1.780.424.7663. Mail to: 3428 99 Street NW Edmonton, Alberta T6E-5X5. We service all of Alberta including Edmonton, Stony Plain, Spruce Grove, Fort Saskatchewan, St Albert, Sherwood Park, Leduc, Nisku, Beaumont, Lac La Biche, Grande Prairie, High Level, Westlock, Slave Lake, Edson, Drayton Valley, Devon, Camrose, Wetaskiwin, Tofield, Lamont, Morinville, Vegreville, Millet, Calmar, Evansburg, Redwater, Onaway, Viking, Athabasca, High Prairie, Valleyview, Fairview, Peace River, Whitecourt, Mayerthorpe and many more rural areas and towns.  

Edmonton Roof Snow and Ice Removal, March 2013

This client reached out to GRS to have the ice and snow cleared off of the front half of their residence's roof. GRS drove out of town to assist these clients in preventing a serious buildup of potentially damaging snowfall. Roof Report: March 26, 2013 Our team drove out to the client's location for 11:30am. The team of two took a look at the roof, and found that it's in very good condition. As a brand new shingle roof, there was almost no worry that the snowpack had caused any further lasting damages. Snow and ice was built up in the valleys of the roof, with some slight water damage problems inside [Editor's Note: The report received does not clarify whether the problems had been around before this particular snowfall, or they were a result of it]. There was no problem with the back half of the building's roof, so only the front was cleared off. The crew departed at 4:30pm, each putting in five hours to this service call.   image001 image002 image003 image004 image005 image006 image007   CODE: 54042 Contact Us Call our 24 hour emergency roof repair at 1.780.424.7663. Mail to: 3428 99 Street NW Edmonton, Alberta T6E-5X5. We service all of Alberta including Edmonton, Stony Plain, Spruce Grove, Fort Saskatchewan, St Albert, Sherwood Park, Leduc, Nisku, Beaumont, Lac La Biche, Grande Prairie, High Level, Westlock, Slave Lake, Edson, Drayton Valley, Devon, Camrose, Wetaskiwin, Tofield, Lamont, Morinville, Vegreville, Millet, Calmar, Evansburg, Redwater, Onaway, Viking, Athabasca, High Prairie, Valleyview, Fairview, Peace River, Whitecourt, Mayerthorpe and many more rural areas and towns.

Roof Snow Removal and Leak Repair in Saskatoon, March 2013

Below you will find two field reports for a commercial snow removal in Saskatoon, Saskatchewan. Snow buildup had been implicated as a cause of leaks in the client's office.
March 1 2013:
We arrived on-site in the afternoon and measured the roof, which was a bit larger than our initial estimates. There is a leak in the client's office, so we cleared out about 150 sq. ft. around the leak area (first photo).
Better shovels are on the material list for tomorrow so we can work a lot more efficiently.
image image[1] image[2] image[3]
March 2 2013:
Above the client's office, there are a lot of improperly sealed spots that need work, which are causing the leak. Two segments of the building have had their snow removed in preparation. If the water that leaked into his office is not drained properly, there is going to be a big problem here pretty soon.
image (1) image[2] image[3] image[4] photo
< End Report >
Code: 3910
Contact Us Call our 24 hour emergency roof repair at 1.780.424.7663. Mail to: 3428 99 Street NW Edmonton, Alberta T6E-5X5. We service all of Alberta including Edmonton, Stony Plain, Spruce Grove, Fort Saskatchewan, St Albert, Sherwood Park, Leduc, Nisku, Beaumont, Lac La Biche, Grande Prairie, High Level, Westlock, Slave Lake, Edson, Drayton Valley, Devon, Camrose, Wetaskiwin, Tofield, Lamont, Morinville, Vegreville, Tofield, Millet, Calmar, Evansburg, Redwater, Onaway, Viking, Athabasca, High Prairie, Valleyview, Fairview, Peace River, Whitecourt, Mayerthorpe and many more rural areas and towns.

Edmonton Industrial Metal Roof Repair, September 2011

This client needed repairs done to their metal roof on an industrial building of theirs. They reached out to GRS for quotation on repair or replacement options, which we provided to them with our recommendation for replacement. Due to the nature of metal roofing, expansion and contraction in Canada's climate can be a hassle, and repairs are not always the best option to extend the life of the roof.
Table of Contents
  Assessment: September 22, 2011 We sent out one of our crew members to perform an inspection on the roof. The following is from their report: There are two roofs at hand. The upper metal deck measuring 110' x 95', which has eight 12" roof jacks, one air conditioning unit, and one gum box for a 3" gas line. The roof appears to be leaking from seams around the perimeter. The gas line with the gum box is exposed, and all eight roof jacks require resealing. There is a 20' piece of metal flashing missing from the northwest parapet. The lower roof has a metal deck measuring 25' x 50'. I recommend that the high-low wall caulking be redone. The seams around the perimeter also appear to be source of leaks. Edmonton-20110922-00463 Edmonton-20110922-00464 Edmonton-20110922-00465 Edmonton-20110922-00467 Edmonton-20110922-00468 Edmonton-20110922-00469 Edmonton-20110922-00470 Edmonton-20110922-00473 Edmonton-20110922-00474 Edmonton-20110922-00475 Edmonton-20110922-00476 Edmonton-20110922-00477 Edmonton-20110922-00478 Edmonton-20110922-00480 Edmonton-20110922-00481 IMG-20110922-00457 IMG-20110922-00458 IMG-20110922-00459 IMG-20110922-00460 IMG-20110922-00461 IMG-20110922-00462 IMG-20110922-00466 IMG-20110922-00471 IMG-20110922-00472   Quotation Delivered: September 26, 2011 The client sought quotation for repairs to their industrial metal roofing system. When returning the quotation, we noted that the issue, specifically to this roof, is that it is at the point where it should be coated or replaced. Spot repairs will likely bring more aggravations as the expansion and contraction of seams, fasteners, penetrations, etc. is at the point where spot repairs likely won't last long and would come with no guarantees. After receiving the quotation, the client wrote back to request that spot repairs be made. They are currently planning renovations to the building, and will likely have to put some more holes into the roof during that time. Once that is done, they would be open to re-evaluating any roof recovery or coating, but for the time being, the spot repairs will be sufficient. They also noted that in the wintertime there are serious concerns about ice buildup and icicles coming from the eavestroughs, and would like to have them replaced with continuous eaves. We scheduled the client for service three weeks later, and noted that we'll measure the eaves in the meantime. Typical turnaround time on eaves of that length, however, can be up to a month.   Roof Report: October 30, 2011 We arrived on site in the morning and filled out all of the necessary safety documentation. The aerial lift was missing a certificate, so we had it switched out for another one and used a pull-rope hoist to get the tools onto the roof in the meanwhile. Once on the roof, two members began sweeping and shovelling the snow off the roof and chipped away thick segments of ice to clean up the areas where repairs would be done. The new lift came in with an appropriate certificate and was presented to the client. We cleaned out the eavestroughs on the front of the building and dealt with the ice buildup that the client had noted some weeks earlier. In the early afternoon, however, heavy snowfall rolled in and hindered work. The team departed the worksite after storing the tools. IMG_2433 IMG_2434 IMG_2435 IMG_2436 IMG_2437 IMG_2438 IMG_2439 IMG_2440 IMG_2441 IMG_2442 IMG_2443 IMG_2445 IMG_2446 IMG_2447 IMG_2450 IMG_2451 IMG_2452 IMG_2453 Roof Report: November 2, 2011 The team arrived on site again to find themselves met with the previous day's snowfall and ice buildup once again. Save for a lunch break, the bulk of the day was spent removing snow and ice buildup from the eavestroughs and clearing the worksite. IMG_2489 IMG_2488 IMG_2487 IMG_2513 IMG_2512 IMG_2511 IMG_2510 Edmonton-20121102-00243 Edmonton-20121102-00241 Edmonton-20121102-00240 Edmonton-20121102-00239 Edmonton-20121102-00238 IMG_2453 IMG_2452 IMG_2451 Roof Report: November 3, 2011 This day saw even more ice and snow cleared from the eavestroughs and the roof in preparation for the rubber application. Shortly after finishing the worksite preparation, they had set up the pump, mixed the saltwater solution and stirred the rubber. 75% of one side was finished in the day, with an estimated 3.5 - 4 hours worth of rubber spraying to finish the following day. The pump was cleaned out, and the team packed up for the day. Roof Report: November 4, 2011 Back on site, the team scraped off a small amount of ice that had built up overnight. They set up the liquid rubber pump and sprayed the remaining sections of the roof. Afterwards, a beauty cap was ordered to be later fastened to the building, and the pump was cleaned out to specification. The remaining work to be completed is the beauty cap, 9" rain caps (to replace some broken ones), and fasten the new eavestroughs once the ice has melted away. IMG_2518 IMG_2519 IMG_2520 IMG_2521 IMG_2522 IMG_2523 IMG_2524 IMG_2525 IMG_2526 IMG_2527 IMG_2528 IMG_2529 IMG_2530 IMG_2531 IMG_2532 IMG_2533 IMG_2534 IMG_2535 IMG_2540 IMG_2542 IMG_2543 IMG_2544 IMG_2545 IMG_2546 IMG_2547 IMG_2548 IMG_2549 IMG_2550 IMG_2551 IMG_2552 IMG_2553 IMG_2554 < End Report > CODE: 11211 Contact Us Call our 24 hour emergency roof repair at 1.780.424.7663. Mail to: 3428 99 Street NW Edmonton, Alberta T6E-5X5. We service all of Alberta including Edmonton, Stony Plain, Spruce Grove, Fort Saskatchewan, St Albert, Sherwood Park, Leduc, Nisku, Beaumont, Lac La Biche, Grande Prairie, High Level, Westlock, Slave Lake, Edson, Drayton Valley, Devon, Camrose, Wetaskiwin, Tofield, Lamont, Morinville, Vegreville, Tofield, Millet, Calmar, Evansburg, Redwater, Onaway, Viking, Athabasca, High Prairie, Valleyview, Fairview, Peace River, Whitecourt, Mayerthorpe and many more rural areas and towns.