Commercial Roofing Sherwood Park. June 15, 2015.

Article: Flat Roof Replacement (Recovery). Commercial Roofing Sherwood Park, Alberta.

The roof report below is a commercial roofing project in Sherwood Park, Alberta. It was a liquid rubber flat roof replacement (recovery). We also installed pitch pocket extensions, caps for pitch pockets, and grease trays on the roof. Commercial Roofing Sherwood Park. There were two primary challenges with this flat roof system. The first was that the rooftop units could not be shut down as the restaurant below needed them. And the second challenge was doing roof maintenance with-out removing units in such a small confined space. The decision was made to coat the flat roof with a liquid rubber coating instead of attempting spot repairs. This would enable repairs to be done with-out disrupting the business operation. We also extended pitch pockets, capped pitch pockets no longer in use, and installed proper grease trays so that the grease didn't break down the roof membrane. July 7, 2014: Crew Arrives On Site For Commercial Roof Pre-Install Meeting.  Site Location: 194 Ordze Avenue Sherwood Park, Alberta. I met with the client and did a pre-install meeting with him. I took all my measurements for pitch pocket extensions, new grease trays and caps for obsolete pitch pockets. I then went to the shop to get the metal fabricated. They will be done tomorrow late afternoon. This roof might take me two days - there is a lot of prep work and a lot of metal that has to come off and then be put back on to get the job done right. July 8, 2014: Crew Arrives at Commercial Roof Site To Complete Prep Work.  When we arrived on site we loaded our tools to the roof and started taking off the loose gravel (which was really excessive and coated in grease). After getting gravel off the roof we spud-ed out about a quarter of the roof but the hotter it got the spud would just wreck the roof so I notified project management of this and our customer. I informed our customer I would be back when temperatures cooled down with in a week or so and customer was fine with this. July 11, 2014: Crew Arrives Back On Site.  Today we finally got the roof spud-ed and it wasn't easy but we got it done. After that we cleaned the roof by hand cause I didn't want to use pressure washer on roof with customers walking nearby and vehicles in parking lot. But by the end of the day we got about 50% of our mesh on our detail and all the holes patched the job is 75% complete all that is left is finish around the unit then roll our rubber out and get the garbage off the roof. Site will be complete tomorrow.
Commercial Roofing Sherwood Park - Earls Restaurant Sherwood Park, Alberta
Commercial Roofing Sherwood Park - Earls Restaurant Sherwood Park, Alberta
Mesh Along Metal with liquid rubber.
Mesh Along Metal with liquid rubber.
Roof Spuded and prepped.
Roof Spud-ed and prepped.
Penetrations Sealed
Penetrations Sealed
Prep Work
Prep Work
  July 12, 2014: Crew Arrives On Site To Complete Liquid Rubber Recovery. Today we finished our prep work around the units, then we installed our pitch pocket extensions to 6 inch. While Ray and I rolled the roof I had the other guys download all the garbage to the truck to take to the dump. After first coat dried we applied a second coat. Material used. 3 pails of brush grade liquid rubber. Half pail of trowel grade liquid rubber. 1 can Sopra mastic. 120 ft of 6 inch mesh. 4 paint brushes. 2 rollers.
Liquid Rubber Flat Roof Recovery
Liquid Rubber Flat Roof Recovery
Liquid Rubber Flat Roof
Liquid Rubber Flat Roof
Liquid Rubber Roof
Liquid Rubber Roof
Liquid Rubber Recovery
Liquid Rubber Recovery
Liquid Rubber
Liquid Rubber
  August 5, 2014: Crew Arrives To Install Patio Stone Walkway.  The crew installed 11 patio stones with high dense foam underneath for a walk way to service units and grease traps.
Patio Walkway
Patio Walkway
Patio Stones
Patio Stones
Walkway Installed
Walkway Installed
  Article topics: Commercial Roofing Sherwood Park, Alberta.   < End of Report >   CONTACT US Call our 24 hour emergency roof repair at 1.780.424.7663. Mail to: 3428 99 Street NW Edmonton, Alberta T6E-5X5. For other areas of Canada call us at 1.877.497.3528 toll-free. We service all of Alberta including Edmonton, Stony Plain, Spruce Grove, Fort Saskatchewan, St Albert, Sherwood Park, Leduc, Nisku, Beaumont, Lac La Biche, Grande Prairie, High Level, Westlock, Slave Lake, Edson, Drayton Valley, Devon, Camrose, Wetaskiwin, Tofield, Lamont, Morinville, Vegreville, Tofield, Millet, Calmar, Evansburg, Redwater, Onaway, Viking, Athabasca, High Prairie, Valleyview, Fairview, Peace River, Whitecourt, Mayerthorpe and many more rural areas and towns.  

Whitecourt Industrial Liquid Rubber Roof Coating, June 9 2015

Article: Liquid Rubber Roof Coating. Industrial Waterproofing. Whitecourt, Alberta.

This is a site report for a liquid rubber roof coating to waterproof an industrial standing seam metal roof in Whitecourt, Alberta. Roof maintenance coatings will extend the life of a metal roof for many years avoiding costly roof replacement.

We started applying liquid rubber to metal roof systems in Canada about six years ago.

At first we were concerned because many of the elastomeric roof coatings are manufactured for the wider market - which is the USA. Of course this causes a challenge because most of the USA needs reflect or white roof coatings due to the temperature. If you have more warm days than cold days it is best to use a white or cool roof coating in most instances. If you have more cold days than warm days then a dark coating is typically the best choice.

We used various elastomeric coatings in various areas of Canada and over time came to be most confident in applying liquid rubber.

Engineered coatings with advanced polymer technology has changed the game for coating roofs in Canada.

Now that we have millions of square feet of coatings on roofs in Canada we can confidently say that liquid rubber is the best coating you can get for cold climates.

Some Liquid Rubber Facts and Ten Benefits of Using Liquid Rubber on Metal Roofs:

  1. Liquid rubber will waterproof your metal roof. It is monolithic. In other words, when we coat a roof everything is tied in to the main coating. The penetration holes, the parapet walls, the flashing, curbs, crickets and more. There is nowhere for the water to back up or penetrate openings. This is the primary advantage of a coating vs. a membrane system or a metal panel system.
  2. It is a rust inhibitor. If you have a metal roof that is either rusting or will rust due to the materials stored inside, liquid rubber is the best choice.
  3. It is a net benefit for building efficiency in cold climates. Recent studies have confirmed what we knew all along. Simply google key word phrases such as "cool roofing studies for cold climates" and you will find that coating a roof with a cool or white coating in a cold climate is not a wise decision.
  4. It will melt ice dams quicker and it will melt ice in the gutter quicker. A common problem with metal roof systems in cold climates is ice. When ice dams form they cause havoc with metal roof seams between panels, roof vents and curbs and ice in the gutter can "wick" up and under the eave area and melt and cause leaks at the inner wall. We can tie in the gutter system, the wall area and the roof with liquid rubber so no ice can "wick" in to your roof system.
  5. Coating industrial, commercial and any sort of internal gutter system with liquid rubber will solve a lot of problems you may be experiencing with your gutter systems. Especially troublesome are steel erected buildings with parapet walls that have low slope metal roofs and internal gutter systems along the inside of the parapet walls. Liquid rubber can solve that by tying the roof, the gutter and the parapet wall all together as one monolithic membrane system.
  6. It is UV stable. It does not need a reflective coating. It does not need pea gravel. It doesn't peel and crack in the sun.
  7. Liquid Rubber is non toxic, VOC free and solvent free. It cures to provide a seamless, fully adhered flexible membrane. It protects from UV, salt, thermal cycling and harmful chemicals. It is both worker and environmentally safe and is available for commercial, industrial and residential markets.
  8. When we coat your roof it is considered a maintenance invoiced service. Many customers tell us there are tax benefits to maintenance vs. replacement. Check with your accountant.
  9. Liquid Rubber works well in cold climates. It has an expansion rate of up to 1000%. Unlike other products, buildings that have liquid rubber installed by us in cold climates with heavy snow loads are doing well. We have liquid rubber installations in the coldest areas of Canada with snow loads over ten feet and liquid rubber has performed like no other product we can find (specifically for cold climates).
  10. It has an excellent cost value. In other words, to replace a standing seam industrial roof it can cost between 9.00 - 30.00 per square foot. Liquid rubber is a fraction of the cost. It has a ten year warranty with an optional twenty year service agreement available from us. If you need R value, we can spray your roof with foam and cover it in liquid rubber. But if you just need waterproofing, liquid rubber is all you need.

Visit our main web site for more information on Liquid Rubber Roof Coatings.

Here's a video showing our crews at work and the scope of work typically followed when coating metal roof systems:

Below is the roof coating crew's account of this liquid rubber installation.

November 7, 2014: Crew attends to site location near Whitecourt, Alberta.

This is a electrical sub station that added an addition on to their building. The first deficiency was where they joined the building together there was an open split on both sides. Water was running down and leaking in to the building. I sealed it in with seam tape and Liquid Rubber. After that we prepared the roof fasteners, seams, etc and then we started to roll in the roof. We didn't spray this roof because it was smaller in size. Unfortunately it started to rain when we got to the 70% mark and there is rain in the forecast for many days. We will have to return at a later date to finish the coating.

Metal roof seam issue where roofs were connected that needs waterproofing.
Metal roof seam issue where roofs were connected that needs waterproofing.
Standing seam metal roof before liquid rubber roof coating.
Standing seam metal roof before liquid rubber roof coating.
Liquid rubber coating applied to seventy percent of building.
Liquid rubber coating applied to seventy percent of building.
Industrial metal roof coating with liquid rubber.
Industrial metal roof coating with liquid rubber.

April 14, 2015: Roof Coating Crew Re-Attends to Site.

When we finished 70% of the roof last season the rain came in and lasted for days and then turned in to a snow storm so this roof had to be completed spring of 2015 when weather was suitable enough to apply liquid rubber.

9:50 am arrived on site.

We  arrived on site and we did our daily tool box meetings. We then did a site orientation with the engineering company who hired us. 11:00 am we got on the roof.  One of us started painting the ribs with Liquid Rubber while I started coating panels with Liquid Rubber. We coated about 1100 sq. ft. It took awhile due to the slope of the roof.  At the end of the job the customer looked over the work and was very happy.

2:10  pm leave site.

Workers ropes tied off on tin roof.
Workers ropes tied off on tin roof.
GRS Worker, applying Liquid Rubber.
GRS Worker, applying Liquid Rubber.
Finished Section of roof with Liquid Rubber Applied.
Finished Section of roof with Liquid Rubber Applied.
Roof Half finished with Liquid Rubber.
Roof Half finished with Liquid Rubber.
Close up of the liqid Rubber applied to roof.
Close up of the liquid rubber applied to roof.
  < End of Report >
CONTACT US
Call our 24 Hour Emergency Roof Repair at 1.780.424.7663. Mail to: 3428 99 Street NW Edmonton, Alberta T6E-5X5.
For all other areas of Canada call 1.877.497.3528 Toll Free.
We service all of Alberta including Edmonton, Stony Plain, Spruce Grove, Fort Saskatchewan, St Albert, Sherwood Park, Leduc, Nisku, Beaumont, Lac La Biche, Grande Prairie, High Level, Westlock, Slave Lake, Edson, Drayton Valley, Devon, Camrose, Wetaskiwin, Tofield, Lamont, Morinville, Vegreville, Tofield, Millet, Calmar, Evansburg, Redwater, Onaway, Viking, Athabasca, High Prairie, Valleyview, Fairview, Peace River, Whitecourt, Mayerthorpe and many more rural areas and towns.

Athabasca DecTec Balcony Assessment, February 2015

Our client, located north of Edmonton, reached out to GRS to explore the option of installing DecTec Membrane on a balcony off the second floor of their building. Scope of Work: 1) Removal and disposal of existing roof assembly under the existing membrane that would interfere with new surface installation. 2) Removal/replace rotten sheathing (if any). 3) Mild increase to slope to encourage drainage. 4) Door openings may have to be customized to account for new slope. 5) Flashing may have to be re-done to accommodate new slope as well. 6) Deck railing removed and replaced to ensure safety. 7) Waterproofing of walls to allow for vertical installations. Ensures watertight fit. 8) Upon completion of 1-7 (as necessary), floating deck can then be installed to support viable systems (SBS Modified Torch, EPDM, TPO, or PVC), though DecTec does not require a floating deck to sit atop the membrane.   Proposed Solution DecTec bore GRS's recommendation for this project, as we employ all of the technicians typically required to see a successful installation. The client was simply looking for a quote for this type of project, which we were happy to provide.   Existing Decking: Pre-DecTec Installation 1 Pre-DecTec Installation 2 Pre-DecTec Installation 3 Pre-DecTec Installation 4 Pre-DecTec Installation 5 Pre-DecTec Installation 6     Until next time,         The Roofers at GRS CODE: 4510 Contact Us Call our 24 hour emergency roof repair at 1.780.424.7663. Mail to: 3428 99 Street NW Edmonton, Alberta T6E-5X5. We service all of Alberta including Edmonton, Stony Plain, Spruce Grove, Fort Saskatchewan, St Albert, Sherwood Park, Leduc, Nisku, Beaumont, Lac La Biche, Grande Prairie, High Level, Westlock, Slave Lake, Edson, Drayton Valley, Devon, Camrose, Wetaskiwin, Tofield, Lamont, Morinville, Vegreville, Tofield, Millet, Calmar, Evansburg, Redwater, Onaway, Viking, Athabasca, High Prairie, Valleyview, Fairview, Peace River, Whitecourt, Mayerthorpe and many more rural areas and towns.  

Engineered Liquid Rubber Roof Recovery in Edmonton AB, October 2014

Below you will find a quotation, project manager notes, and a field report for an engineered liquid rubber roof recovery for an industrial metal roofing client in Edmonton, Alberta. Quotation, October 15 2014:
  • Engineered liquid rubber recovery to complete metal roof.
  • Pressure washing to clean, water test, and assess.
  • Fasteners will be tested and replaced as required to complete the roof deck, penetrations, and gutters.
  • Sheet metal repair and penetration saddle fabrication as required.
  • Remove old caulking as required.
  • Hand trowel all penetrations, roof to wall connections, fasteners, ridge, horizontal sheet seams, hidden gutters, and roof edge at external gutters with mesh and high grade rubber as required.
  • Apply liquid rubber coating, allow cure time, repeat hand trowel process above, and apply second coat of liquid rubber.
  • Liquid rubber to full inside face of parapet and top of parapet cap.
  • Ten year manufacturer warranty is extendable to twenty year maintenance agreement.
Project Manager Notes This roof structure may be a candidate for either a repair-maintenance program or an engineered liquid rubber coating - you may not have to replace it. I would not recommend a standard reflective elastomeric coating, or the SPF spray foam (with standard reflective coating), as this standard does not last well in a Western Canadian climate. Liquid rubber performs well in our climate as it has up to a 1200% expansion/contraction rate. If considering SPF for R-value, we strongly suggest covering the spray foam with liquid rubber or EPDM. Our crews do this work everyday with success. Generally speaking, metal roof systems are constant aggravating roof structures. Industrial systems have a deficient design - they are water-shedding, and not waterproofing, coverings. Metal expands and contracts more than any other roofing material and tend to leak from ice/snow loads. Leaks are also intermittent at seams (vertically where sheets are seamed together and horizontally where seams meet between sheets), penetrations, fasteners, around the perimeters at gutters, under the eaves, and at joints between roof and wall connections. Rust and corrosion may also develop. Traditional caulking or coating lasts a few seasons at best. Remedies are either spot repairs - maintenance with caulking or engineered coatings. Our recommendation in this instance is a high and engineered 2-ply liquid rubber polymer coating with a 10 year warranty, with the option of a 20 year maintenance contract for extended leak protection. Our client approved the quotation the same day for a roof recovery. Field Report, October 22 2014: After picking up the liquid rubber, we went to the work site and prepared the roof with seam tape around all seam tapes and penetrations. We then began coating the roof with liquid rubber and completed this site by the evening.
20141020_141353_resized
Seam taping around units
20141020_164201_resized
Coating begins
20141020_141400_resized
Assessment
20141020_141654_resized
Scoping ventilation units
20141020_141701_resized
Low-slope valleys
20141020_141707_resized
20141020_164303_resized
Coating around B-vent
20141020_162526_resized 20141020_164209_resized 20141020_164217_resized liquid 20141020_164257_resized 20141020_164320_resized 20141021_150726_resized 20141021_150734_resized 20141021_150743_resized < End Report > Code: 9222 Article Topics: Industrial Metal Roof Coating Edmonton, Alberta. Liquid Rubber.   Contact Us 24 Hour Emergency Roof Repair. Telephone: 1.403.873.7663. Email: info@calgaryroofrepair.ca. Mailing: 240 – 70 Shawville Boulevard SE Calgary, Alberta. T2Y 2Z3. For all other areas of Canada call 1.877.497.3528 Toll Free. We service all areas of southern and central Alberta and south east British Columbia including Airdrie, Banff, Calgary, Canmore, Crossfield, Carstairs, Didsbury, Olds, Sundre, Three Hills, Drumheller, Hanna, Brooks, Bassano, Strathmore, Chestermere, Irricana, Cochrane, Black Diamond, Okotoks, Priddis, Bragg Creek, Cranbrook, Fernie, Panorama, High River, Vulcan, Medicine Hat, Lethbridge, Taber, Sylvan Lake, Red Deer and other Alberta rural points between.

Sherwood Park Commercial Roof Resurfacing, July and August 2014

Below is a series of field reports for repairs done to a commercial property by the Edmonton roofing repair crew. Our initial assessment showed that the roof was an ideal candidate for a complete replacement due to the large scale of repairs which were quoted.  Scope of Work:
  • Complete roof resurfacing including:
    • Gravel removal.
    • Spudding.
    • Cleaning.
    • Membrane resurfacing.
  • Two coats of liquid rubber.
  • Removal of all obsolete pitched pockets, with the extension of the current active pockets to a minimum of 6 in.
  • Fabrication of custom sheet metal grease trays
Field Report, July 7 2014: After completing a pre-install meeting with the customer, we took measurements for the pitch pockets, grease trays, and pitch pocket caps. We then went to the shop for a material requisition and they advised us our order would be ready for tomorrow afternoon. Our crew delivered the scope of work as promised over the next few weeks. As we had anticipated, this series of spot repairs was only temporary and it was only a matter of time until our client called us back. Ideally, we would like to see this particular site undergo a complete replacement since the structure's sustainability is running out and will only require more repairs as time goes by.
Field Report, August 5 2014:
Today we installed a full length safety railing along the eaves of the roof. We began by loading 11 patio stones and high density foam to the roof. We then installed the walkway and took our client on a tour of the completed work. He was pleased with the repairs.
< End Report >
Code: 194
CONTACT US:
Call our 24 hour emergency roof repair at 1.780.424.7663. Mail to: 3428 99 Street NW Edmonton, Alberta T6E-5X5. Email: info@grscanadainc.com. We service all of Alberta including Edmonton, Stony Plain, Spruce Grove, Fort Saskatchewan, St Albert, Sherwood Park, Leduc, Nisku, Beaumont, Lac La Biche, Grande Prairie, High Level, Westlock, Slave Lake, Edson, Drayton Valley, Devon, Camrose, Wetaskiwin, Tofield, Lamont, Morinville, Vegreville, Tofield, Millet, Calmar, Evansburg, Redwater, Onaway, Viking, Athabasca, High Prairie, Valleyview, Fairview, Peace River, Whitecourt, Mayerthorpe and many more rural areas and towns.

Engineered Liquid Rubber Metal Roof Recovery Ponoka Alberta, May 2014

Below you will find a series of reports from scope of work to completion for a large industrial metal roofing coating project. The Ponoka roofing repair crew provided the following assessment: Scope of Work, May 12 2014: The metal roof will be completed using two-ply engineered liquid rubber recovery. A pressure wash will be used to cleaning, water testing, and for site assessment. Test and replace fasteners as required to complete roof deck, penetrations, and gutters. We will provide sheet metal repair and penetration saddle fabrication as required, as well as remove old caulking. All:
  • Penetrations
  • Roof-to-wall connections
  • Fasteners
  • Ridge, horizontal sheet seams
  • Hidden gutters, and roof edging at external gutters
will be hand-troweled using mesh and high grade rubber as required. Liquid rubber coating will then be applied, allowing a cure time, followed by a repeated hand trowel process as above. This will be followed by a second coat of liquid rubber. The project manager provided a rationale for using engineered coating as well. Although the industrial standard would have been to recommend reflective elastomeric coating or SPF spray foam, they do not have longevity in a Western Canadian climate. Liquid rubber, on the other hand, has been shown to have a 1200% expansion and contraction rate. The idea was to get the "most mileage" out of the metal roofing, which have a high maintenance turnover due to leaks caused by expansion and contraction of the metal. Expenses also increase with wear and tear caused by corrosion. Using high end engineered liquid rubber polymer in this climate and context would skirt many of these ongoing maintenance problems.
Preparation was dirtier than expected
Preparation was dirtier than expected
Old caulking to be removed
Old caulking to be removed
Contract is approved and work begins, June 22 2014:
Before caulking removal
Before caulking removal
After caulking removal
After caulking removal
The Ponoka roof repair crew arrived on-site and completed work on all seams, corners, and details with mesh and liquid rubber, as detailed. A first coat of trowel and liquid rubber brush-grade was applied.
20140621_122017_resized
Initial coating
20140621_121949_resized
Coating around ventilation systems
20140621_145807_resized
Flat metal roofing coats
  Roof completed, June 23 2014: Gutter seams completed using mesh, second rubber layer coated onto the roof.
Rolling liquid rubber
Rolling liquid rubber
Making progress
Making progress
Finished product
Finished product
< End Report > Code: PON Contact Us Call our 24 hour emergency roof repair at 1.780.424.7663. Mail to: 3428 99 Street NW Edmonton, Alberta T6E-5X5. We service all of Alberta including Edmonton, Stony Plain, Spruce Grove, Fort Saskatchewan, St Albert, Sherwood Park, Leduc, Nisku, Beaumont, Lac La Biche, Grande Prairie, High Level, Westlock, Slave Lake, Edson, Drayton Valley, Devon, Camrose, Wetaskiwin, Tofield, Lamont, Morinville, Vegreville, Tofield, Millet, Calmar, Evansburg, Redwater, Onaway, Viking, Athabasca, High Prairie, Valleyview, Fairview, Peace River, Whitecourt, Mayerthorpe and many more rural areas and towns.

St. Albert Liquid Rubber Roof Coating, July 2013

This report is the first in a series of repairs and services that GRS has carried out for this particular client and their residential roofing system. The first covers a liquid rubber application to seal up some leaks in the existing roof. The article will be updated with links [at the bottom of this page] once the other reports have been posted. Quotation Delivered: June 13, 2013 GRS delivered a quotation to the client, detailing both the replacement and roof recovery options available to their existing roofing system. The client elected to move forward with an engineered liquid rubber roof recovery, so we booked them in for service to commence shortly.   Roof Report: July 16, 2013 The crew arrived on site for 4:30pm, setting up the area for the work to be carried out. Come 8:00pm, the site was fully prepared and the crew departed for the evening.   Roof Report: August 2, 2013 The GRS team went back to the client's site to get back to working on the recovery. The bulk of the day consisted of removing as much of the Portland cement as possible, and identifying all the possible areas of water ingress. Once the cement had been cleared out, they applied Barr squeegee-grade over the affected areas to smooth out the surface. The final task for the day was spraying on a flood coat of the liquid rubber, using up around one-third of the barrel of solution. With the leaks dealt with, the team departed the job site, considering it complete. Regrettably, there are no photos for this project that remain accessible - please accept our apologies! The featured image above is from a later project at the same location, giving an indication of the roof's status.   Follow-up Visits to the Site: http://edmontonroofrepair.ca/st-albert-liquid-rubber-roof-repair-december-2013/ http://edmontonroofrepair.ca/st-albert-temporary-tarp-roof-repair-december-2013/ http://edmontonroofrepair.ca/st-albert-liquid-rubber-roof-recovery-july-2013-2/   CODE: 60 Contact Us Call our 24 hour emergency roof repair at 1.780.424.7663. Mail to: 3428 99 Street NW Edmonton, Alberta T6E-5X5. We service all of Alberta including Edmonton, Stony Plain, Spruce Grove, Fort Saskatchewan, St Albert, Sherwood Park, Leduc, Nisku, Beaumont, Lac La Biche, Grande Prairie, High Level, Westlock, Slave Lake, Edson, Drayton Valley, Devon, Camrose, Wetaskiwin, Tofield, Lamont, Morinville, Vegreville, Millet, Calmar, Evansburg, Redwater, Onaway, Viking, Athabasca, High Prairie, Valleyview, Fairview, Peace River, Whitecourt, Mayerthorpe and many more rural areas and towns.  

Edmonton Tar and Gravel Roof Recovery, October 2012

This client in Edmonton sought a quote from GRS for the services available to their failing tar and gravel roof system. We returned the quote to them, helped make the best selection for their situation, and followed through with the service. We first heard from this client in mid-September and assessed their property for viable solutions to their problem. We returned our usual quotation to them, which included pricing for temporary repairs, roof recovery, or roof replacement systems. The client was hoping for a single recommendation in terms of viability, as they weren't sure what each solution entailed. We recommended roof recovery via liquid rubber or EPDM system to give the same longevity of a total replacement, but at a lesser cost. The client elected for an EPDM system installation, and we got to scheduling the job. For mid-October, we began clearing space for a waste bin and prepared the site for the technicians to come in for the installation. IMG_8042 IMG_5470 Field Report, October 11 2012: Our crew arrived to the location for 8:30am and worked through to 6:30pm. The bulk of the day was spent removing the on-roof gravel in preparation for the EPDM. Due to the accumulation of ice on the roof, we had to spud it instead to remove the gravel and ice at the same time. The roof is now cleared off and ready to move on to the next phase of the project. 0ct 11 2012 007-Optimized 0ct 11 2012 004-Optimized         0ct 11 2012 005-Optimized0ct 11 2012 006-Optimized 0ct 11 2012 008-Optimized 0ct 11 2012 009-Optimized 0ct 11 2012 010-Optimized 0ct 11 2012 011-Optimized 0ct 11 2012 012 Field Report, October 17 2012: The crew began the EPDM installation for the roof recovery, and had it finished quickly. Below are some in-progress photos and materials used in the job. The metal is yet to be installed, but that should be completed shortly. Materials:
  • 3 rolls of EPDM.
  • 2 Splice Adhesive.
  • 1 Bucket of screws.
  • 1 Bucket of plates.
  • 2 Buckets of primer.
  • 2 Pallets of fiber board.
  • 2 Russ strips.
  • 1 Box of seam tape.
  • 3 Pails of Mulehide bonding adhesive.
  • 8 Roller sleeves.
  • 2 Roller cages.
  • 2 boxes of regular silicone.
  • 1 box of sealant.
photo (53) photo (57) photo (56) photo (55) photo (54) < End Report > CODE: 14014 Contact Us Call our 24 hour emergency roof repair at 1.780.424.7663. Mail to: 3428 99 Street NW Edmonton, Alberta T6E-5X5. We service all of Alberta including Edmonton, Stony Plain, Spruce Grove, Fort Saskatchewan, St Albert, Sherwood Park, Leduc, Nisku, Beaumont, Lac La Biche, Grande Prairie, High Level, Westlock, Slave Lake, Edson, Drayton Valley, Devon, Camrose, Wetaskiwin, Tofield, Lamont, Morinville, Vegreville, Tofield, Millet, Calmar, Evansburg, Redwater, Onaway, Viking, Athabasca, High Prairie, Valleyview, Fairview, Peace River, Whitecourt, Mayerthorpe and many more rural areas and towns.

Roof Soffit and Fascia Repair Edmonton AB, September 18 2012

Below you will find a scope of work, materials list, and field report  by our Edmonton roofing repair crew for a soffict and fascia repair at a commercial client's building.  Scope of Work
  • Roofing (flat, metal, slope).
  • Roof inspection.
  • Exteriors (siding, soffit, fasia).
  • Carpentry.
  • Sheet metal (flashing).
Materials
  • Metal fascia with lettering, per client specification.
  • Plywood.
  • Circular saw.
  • Metal for cap flashing.
Field Report, September 18 2012: We removed the damage fascia, soffit, and cap flashing. A new plywood soffit was cut and re-installed, as well as a fascia with new company lettering. The cap flashing was then added again for weather proofing. As well, we painted the plywood soffit white to match the existing colour, and painted the rest of the siding red. We are still waiting on the client's decision on whether he would like another coat of paint.
Awaiting client approval
Awaiting client approval
  < End Report > Code: 99 Contact Us Call our 24 hour emergency roof repair at 1.780.424.7663. Mail to: 3428 99 Street NW Edmonton, Alberta T6E-5X5. We service all of Alberta including Edmonton, Stony Plain, Spruce Grove, Fort Saskatchewan, St Albert, Sherwood Park, Leduc, Nisku, Beaumont, Lac La Biche, Grande Prairie, High Level, Westlock, Slave Lake, Edson, Drayton Valley, Devon, Camrose, Wetaskiwin, Tofield, Lamont, Morinville, Vegreville, Tofield, Millet, Calmar, Evansburg, Redwater, Onaway, Viking, Athabasca, High Prairie, Valleyview, Fairview, Peace River, Whitecourt, Mayerthorpe and many more rural areas and towns.  

Edmonton Metal Roof Repair, March 2012

The details below cover a metal roof repair for a client's industrial building in Edmonton. Multiple sections of the existing roof are leaking, and they reached out to us for a quotation to put carry out the necessary repairs. The client reached out to GRS for a quotation for the several repairs necessary for their building's metal roof. After examining it, we found six problem spots that would need to be addressed (Shop 1, First Aid Room, Four units on upper level). We returned the desired quote to them, in addition to replacement and liquid rubber options for the lower roof, should they consider that avenue of approach. We advised that the best option for the failing roof would be a engineered liquid rubber application, as metal roofs swell and shrink with temperature changes and are prone to failures of that nature more than any other system. The liquid rubber stretches with the metal, and would be the best bet to have the leaks dealt away with. Repairs were carried out to the problem points, but the failing metal roof sprung more leaks that could not be guaranteed against in the initial repair attempt. We offered re-roofing or roof replacement services at a discount, but the client requested quotations for repairs to other areas of the roof in addition to a snow removal maintenance contract for the upcoming winter. Post will be updated as more information comes in. DSCF0401 Shop 1 North side Shop 1 North side (4) Shop 1 North side (3) Shop 1 North side (2) DSCF0405 DSCF0404 DSCF0403 DSCF0402   CODE: 2103 Contact Us Call our 24 hour emergency roof repair at 1.780.424.7663. Mail to: 3428 99 Street NW Edmonton, Alberta T6E-5X5. We service all of Alberta including Edmonton, Stony Plain, Spruce Grove, Fort Saskatchewan, St Albert, Sherwood Park, Leduc, Nisku, Beaumont, Lac La Biche, Grande Prairie, High Level, Westlock, Slave Lake, Edson, Drayton Valley, Devon, Camrose, Wetaskiwin, Tofield, Lamont, Morinville, Vegreville, Tofield, Millet, Calmar, Evansburg, Redwater, Onaway, Viking, Athabasca, High Prairie, Valleyview, Fairview, Peace River, Whitecourt, Mayerthorpe and many more rural areas and towns.