Spray Foam Roof Repair Request, September 2015, Esterhazy SK

This client in Esterhazy, SK had some problems in 2014 after a big storm. The third-floor rental units of this building had some water damage then, but none since. They reached out to GRS to find a local roofing company that specializes in flat roofs. Our project management worked with them to begin scheduling a team to come out from Regina or Saskatoon. Request For Service: September 24, 2015 The client called in to GRS to see if any roofers could make their way out to the small town of Esterhazy, SK and inspect their roof to see what might've caused water damage in the rental units below a year prior (July 2014). There have been no reports of further water ingress since, but their insurance company required that the roof be attended to before they can proceed with the claim. With Esterhazy, SK being so far away from major centres of operation for GRS, scheduling was a little bit difficult, so the project manager sought as much up-front information as possible about the site and the state of the roof before dispatching crew to go on-site. Submitted Photos: September 25, 2015 The client sent in photos that show the state of the roof and what kind of system the GRS crew would be dealing with upon their arrival. In doing so, it ensures that everybody handling this project with GRS understands what would need to be done in order to correctly patch the roof without any excess travel time such a distance from Regina, where the repair team would be departing from.  
Image 1
The client submitted photos of the initial state of their roof.
Image 2
There were some tears running significant lengths of the roof which required patching.
Image 3
There had been a big storm in 2014, which contributed to water damage and ingress in some of the rental units underneath the roof.
Image 4
A spray foam company had originally installed the roof. Heavy weather conditions resulting in damage are often covered under warranty.
Image 8
There had been some residual water standing that had culminated around blistering that had also formed in the assembly.
Image 10
On top of the blistering, some air/gas bubbles had become trapped. If not addressed, these can eventually lead to tears and holes.
 
Image 15
Wide view of significant standing water over blistered sections of the roof.
Image 17
Tearing and blisters were also found along the perimeter of the roof.
Image 18
The foam joining the roof and the edge flashing was exposed up to the downspout. Water had not been draining correctly, which also culminated into leaks.
  Correspondence: September 25, 2015 The project manager receiving these photos noted the poorly state of the roof system and asked how long ago it was installed. The client responded that it had been installed in 2008 by a Spray Foam company. In dealing with these types of failures, it's important to consider if the system is under warranty or not. Most of the systems and materials that GRS installs on flat roofs come with 20-40 years of expected lifetime and warranty coverage. The project manager relayed this information to the client, as the repairs could be covered by the company that performed the original installation, or the material manufacturer. The client then located the paperwork from the 2008 installation and found that their roof bears a 10-year warranty against leaks. It was at that point that the GRS  project manager advised returning to the original roofing company and advising them of the problems with the structure. The client heeded the advice, and the service request was then closed. < End Report > CODE: 1000 Contact Us Call our 24 hour emergency roof repair at 1.780.424.7663. Mail to: 3428 99 Street NW Edmonton, Alberta T6E-5X5. We service all of Alberta including Edmonton, Stony Plain, Spruce Grove, Fort Saskatchewan, St Albert, Sherwood Park, Leduc, Nisku, Beaumont, Lac La Biche, Grande Prairie, High Level, Westlock, Slave Lake, Edson, Drayton Valley, Devon, Camrose, Wetaskiwin, Tofield, Lamont, Morinville, Vegreville, Millet, Calmar, Evansburg, Redwater, Onaway, Viking, Athabasca, High Prairie, Valleyview, Fairview, Peace River, Whitecourt, Mayerthorpe and many more rural areas and towns.

EPDM Roofing Installation, August 2015, Edmonton

GRS undertook a project re-roofing a large commercial unit with an EPDM roofing system. Everything was brought in and installed with exacting detail from the FR boards to the metal flashings and detail work. Continue reading EPDM Roofing Installation, August 2015, Edmonton

Tar and Gravel Roofing Recovery, July 2011, Edmonton

This report follows repairs made to both levels of a client's tar and gravel roof. The gravel was removed, the roof itself patched and repaired, all before a thorough coating of liquid rubber was applied. Continue reading Tar and Gravel Roofing Recovery, July 2011, Edmonton

Roof Leak Repair in Edmonton AB, December 2014 and July 2015

Below you will find an assessment and field report from the Edmonton roof leak repair crew for a residential client. The roof had been experiencing leaks on two occasions due to a lack of proper ventilation and insulation. Assessment, December 12 2014: By the time we had arrived, the leaking had stopped. However, our client still had buckets out in her kitchen for water collection. The client also showed me the garage, where there appeared to be water damaged on the ceiling. Again, no evident leaking at the time of assessment. A roof inspection was also completed, and we found 4 in. of ice damming.
20141211_140350_resized
Water collection in kitchen
20141211_140354_resized
Interior assessment
20141211_140507_resized
Garage assessment
20141211_141257_resized
Ice damming
20141211_141540_resized
First leak site
20141211_142207_resized
Second leak site
  Installation, July 20 2015: When I arrived on-site, the client showed me two leaks. One was in the living room and another in a bedroom. Both leaks were in line with each other. On the roof, a crack running half the length of the roof was found - the same cracked that was fixed the year before. The crack had probably reoccurred due to a lack of insulation and venting. We fixed the crack again with LR and the client was notified about the insulation and ventilation.
20150718_121643
Crack running the roof length
20150718_121649
Reoccurring crack
20150718_121726
Flooding the area
20150718_123607
LR repair
20150718_123620
LR, post-application
  < End Report > Code: 6407 Contact Us Call our 24 hour emergency roof repair at 1.780.424.7663. Mail to: 3428 99 Street NW Edmonton, Alberta T6E-5X5. We service all of Alberta including Edmonton, Stony Plain, Spruce Grove, Fort Saskatchewan, St Albert, Sherwood Park, Leduc, Nisku, Beaumont, Lac La Biche, Grande Prairie, High Level, Westlock, Slave Lake, Edson, Drayton Valley, Devon, Camrose, Wetaskiwin, Tofield, Lamont, Morinville, Vegreville, Tofield, Millet, Calmar, Evansburg, Redwater, Onaway, Viking, Athabasca, High Prairie, Valleyview, Fairview, Peace River, Whitecourt, Mayerthorpe and many more rural areas and towns.

Nisku Liquid Rubber Roof Recovery, August 2011

The report below follows services carried out on a metal roof for one of our industrial clients. They sought GRS' assistance in recovering their roof with engineered liquid rubber, with some other spot repairs to complete as needed. Inspection: June 2, 2011 The GRS crew went on location to inspect the existing roof system and take photos that will help the project management group form a better idea of what service will be needed at this location. The photos appear below.
100_0006
Our client had an industrial-grade metal roof. A crew was dispatched to perform an initial inspection with regard to the scope and requirements of performing a roof recovery using engineered liquid rubber.
100_0008
Many of the screws were exposed or missing, with parts of the metal beginning to rust.
100_0009
Rusting at the seams, with exposed screws running the length of this section of the roof.
100_0010
There were signs of previous spot repairs. In this case, caulking had been applied to the screws.
100_0011
More spot repairs, with caulking applied at the seams and over the edges. This solution had expired, with cracks forming along the length of the roof where the caulking had been applied over the seams.
100_0012
Closeup of some old sealant applied over seams and around raised screws. Note the hole in the fastener that had previously been closed off. As well, there are slight buckles in the metal. Each of these deficiencies contribute to common leak entry points and a loss of a metal roof's water shedding properties.
100_0013
We inspected the wall connection, noting whether any components on the wall itself needed to be replaced, and whether we had to order any new flashing as part of the recovery.
100_0016
Sealant had previously been applied to the window sills, flashing, along the wall seams, as well as on the intersection between the flashing and the standing seams on the roof. Besides showing signs of cracking, there was also more rusting along the walls.
100_0017
Significant rusting on the flashing, with an unsealed base for the rooftop appliance. As well, the edging over the window sills is not flush with each segment. Further down, it can be seen to be curling up from the window.
  Quotation Delivered: June 6, 2011 After seeing the roofers' investigation photos and measurements, GRS' project management could deliver an accurate quotation for services to be carried out of the roof. Included in the quotation were two separate services; the engineered liquid rubber application and an EPDM installation for the area around two eaves. Also attached to the quotation were the documents and web links surrounding GRS' workmanship guarantee, system methods, schedule availability for the season, and more. There was another note mentioned that regarding schedule availability, it's best to book liquid rubber jobs earlier in the season for when it's warmer. Even though the solution will bond, it performs best when applied in warmer weather.   Roof Report: July 20, 2011 The crew went out to the client's building and got to administering trowel-grade liquid rubber to all penetrations, joints, and problematic areas that has been previously discovered. They also did a lap around the perimeter, ensuring watertightness on the high-risk parts of the roof. They then set up the pump to apply the spray-on liquid rubber and managed to cover roughly one-quarter of the roof itself. Their plan was to finish the entirety of the roof the following day, so they packed up the equipment, cleaned the site, and closed the site for the evening.  
DSC00882
Trowel-grade liquid rubber curing at the base of two plumbing appliances.
DSC00883
Liquid rubber coatings applied and curing at the base of a chimney stack.
DSC00885
We began the roof recovery by applying coatings at the wall connections, paying attention to the penetrations.
DSC00886
A lap around the perimeter was completed to ensure that high risk parts of the roof were protected.
DSC00887
Mid-application over a significantly rusted section of the roof.
DSC00888
By the end of the day, our technicians managed to coat one-quarter of the entire roof.
    Site Inspection: August 1, 2011   One of the senior members of GRS' crew went on-site to inspect the liquid rubber application and found it to be forming a good seal. There was some water that had formed a small bubble in the rubber, but once popped it was deemed fit for continued use as the rubber still formed a solid barrier to the metal.   Roof Report: November 25, 2011 Several months after the initial liquid rubber coating, the client call in to report some other leaks in separate areas of the roof. GRS sent a team out to the site to investigate and carry out the necessary repairs. They administered sealant to the flashing where the wall meets the north-facing roof edge, and again on the south-west corner of the building. They also sealed in the wall-to-roof spots on the west-facing wall and inspected the existing wall spray. After carrying out the spot repairs, they had a better idea of what else needed to be done to the roofing system, and returned the following report:
  • The west-facing wall where the windows are is 3' x 78'. Will need 100' x 6" skrim sheet, and roughly 16 man-hours to install it.
  • The north-facing wall is 3' x 40'. Need 50' x 6" skrim sheet for another 12 man-hours to install.
  • The west-facing wall's upper roof is 3' x 24'. Need 25'x6" skrim sheet and 10 man-hours to finish.
The site was cleaned up, and the crew departed, leaving the repair options in the hands of the client.   This report will be updated as more reports come in, should the client elect to move forward with repairs. CODE: 1409 Contact Us Call our 24 hour emergency roof repair at 1.780.424.7663. Mail to: 3428 99 Street NW Edmonton, Alberta T6E-5X5. We service all of Alberta including Edmonton, Stony Plain, Spruce Grove, Fort Saskatchewan, St Albert, Sherwood Park, Leduc, Nisku, Beaumont, Lac La Biche, Grande Prairie, High Level, Westlock, Slave Lake, Edson, Drayton Valley, Devon, Camrose, Wetaskiwin, Tofield, Lamont, Morinville, Vegreville, Millet, Calmar, Evansburg, Redwater, Onaway, Viking, Athabasca, High Prairie, Valleyview, Fairview, Peace River, Whitecourt, Mayerthorpe and many more rural areas and towns.  

Flat Roof Repair Edmonton Gum Box June 22,2015.

Article: Flat roof repair Edmonton gum box repairs and sealing in a unit with liquid rubber.

The following roof repair report explains a small repair job we completed in Edmonton Alberta. The repairs we needed to complete were filling in rooftop gum cups with mastic. Also we had to seal in a rooftop unit with seam tape and coat it with liquid rubber to waterproof it. Monday June 22, 2015 crew arrives to 12609 153 Ave Edmonton.

12:30 pm arrive on site. Filled out our hazard assessment and safety paperwork forms. The roof repair crew then went on the roof to begin the repairs. Once the crew was on the roof we filled three gum cups using mastic. There was also an rooftop air unit on the roof that the customer asked me to seal in as well. We sealed it in with seam tape and then coated it with liquid rubber with two coats.

We cleaned up the roof and our work site. The customer was happy with the work. We left the site at 2 pm.

Flat Roof Repair Edmonton Gum box filled with mastic.
Gum box at rooftop unit filled with mastic.
Another gum box complete.
Another roof gum-box complete.
Applying seam tape to unit.
Applying seam tape to rooftop unit before applying liquid rubber.
Liquid Rubber applied to unit.
Liquid Rubber applied to unit to waterproof.
 

Materials used. 1 can of mastic. 1 roll of 4 inch seam tape. 1 gallon of LR brush grade.

Man hours to complete repair: 4 hours including drive time 30 min each guy.

CONTACT US Call our 24 Hour Emergency Roof Repair at 1.780.424.7663. Mail to: 3428 99 Street NW Edmonton, Alberta T6E-5X5. For all other areas of Canada call 1.877.497.3528 Toll Free. We service all of Alberta including Edmonton, Stony Plain, Spruce Grove, Fort Saskatchewan, St Albert, Sherwood Park, Leduc, Nisku, Beaumont, Lac La Biche, Grande Prairie, High Level, Westlock, Slave Lake, Edson, Drayton Valley, Devon, Camrose, Wetaskiwin, Tofield, Lamont, Morinville, Vegreville, Tofield, Millet, Calmar, Evansburg, Redwater, Onaway, Viking, Athabasca, High Prairie, Valleyview, Fairview, Peace River, Whitecourt, Mayerthorpe and many more rural areas and towns.
 CODE:12609

Metal Roof Coating Nisku, June 18, 2015.

Article: Metal Roof Coating Nisku Alberta - Liquid Rubber Coating To Industrial Roof.

Liquid rubber expands and contracts very well in Canada's climate. Metal Roofing is the roof that expands and contracts the most out of all roofing material.  June 10, 2014: Crew Arrives on Site for Inspection.  Materials needed. 6 pails of Liquid Rubber. 1 trowel grade. 3 tubed chalking. 1 roll of reinforcement mesh. Man hours 16 to 20 not including drive time. June 14, 2014: Metal Roof Coating Crew Arrives on Site.  Arrived at 511 12 Ave Nisku Alberta. Today we did all our trowel grade and our prep work. Prep work included, patching holes and the center seam all the way down, also our corners. After that we started brushing in where the standing seams are. By the end of the day we had the roof 50% complete.
Prep Work
Prep Work
Prep Work Around Vent
Prep Work Around Vent
Prep Work on Metal Roof
Prep Work on Metal Roof
Liquid Rubber Metal Roof Coating
Liquid Rubber Metal Roof Coating
Liquid Rubber
Liquid Rubber
Metal Roof Coating
Metal Roof Coating
  June 15, 2014: Crew Arrives Back on Site.  Today we finished of the rest of the panels. The roof is 100% complete. I did my walk around with the client and he was extremely happy.   < End Report > CONTACT US Call our 24 hour emergency roof repair at 1.780.424.7663. Mail to: 3428 99 Street NW Edmonton, Alberta T6E-5X5. For all other areas of Canada call us at 1.877.497.3528 toll-free. We service all of Alberta including Edmonton, Stony Plain, Spruce Grove, Fort Saskatchewan, St Albert, Sherwood Park, Leduc, Nisku, Beaumont, Lac La Biche, Grande Prairie, High Level, Westlock, Slave Lake, Edson, Drayton Valley, Devon, Camrose, Wetaskiwin, Tofield, Lamont, Morinville, Vegreville, Tofield, Millet, Calmar, Evansburg, Redwater, Onaway, Viking, Athabasca, High Prairie, Valleyview, Fairview, Peace River, Whitecourt, Mayerthorpe and many more rural areas and towns.

Leduc Metal Roof Repairs, June 17, 2015

Article: Liquid Rubber Spot Repairs to an Industrial Roof in Leduc, Alberta.

Metal roofing expands and contracts more than any other roofing material. The expansion and contraction of seams, fasteners, flashing, gutters and curbs causes leaks. Below is a site report from a repair crew that did metal roof spot repairs to an industrial location in Leduc, Alberta. June 10, 2014: Crew Arrives On-Site for Roof Inspection and to Assess What Material Needed. 7010 45 Street Leduc Alberta.
Materials:
  • 2 pails of liquid rubber.
  • 1 pail trowel grade.
  • 3 tubes caulking.
  • 10 to 12 man hours.
Gutter Needing Repair
Blistering adjacent to a gutter system, with exposed pockets along the edge.
Old Repairs Failing
Old asphalt-based repairs failing along the parapet walls.
Old Repair
Asphalt-based products are most prone to sun (UV) damage. This old repair was past its age due to sun exposure over time, with no touch-ups applied.
  June 18, 2014: Our Leduc Roofing Repair Crew Arrives On-Site for Repairs. Today we cleaned the roof with the pressure washer including the gutter. The gutter took awhile as it had three inches of mud in it. By the end of the day we got most of the units done and the ridge cap complete. I would say about 60% complete. Tomorrow we will finish the gutters and fasteners. We will have site 100% complete tomorrow weather permitting.
Liquid Rubber Applied
Liquid rubber coatings applied to the curb of a rooftop unit.
Liquid Rubber Spot Repairs
Spot repairs using liquid rubber coatings to the metal roof seams and solar tube/skylight curbs.
Liquid Rubber around Vents
Liquid rubber coatings around the base and detailing on vents.
June 20, 2014: Crew Arrives on Site for Completion of Work.  Today we finished all the units and details. I got the other technicians to start the fasteners as we worked on the gutters. We had to coat and line the whole thing with liquid rubber and cloth and then a second coat of liquid rubber. When we finished we helped finish the fasteners and the roof was complete. I got the customer to come up to the roof and do a walk through. He was happy with the work. Materials:
  • 5 Pails of liquid rubber brush grade.
  • 1 pail trowel grade.
  • 2 rolls of 6 inch x 100 ft. rolls of mesh.
  • 6 paint brushes.
  • 2 rollers.
Liquid Rubber Spot Repairs Leduc
Various solar tubes and deficient sections around the standing seams requiring liquid rubber spot coatings.
Liquid Rubber Gutter Coating
Coatings were applied over the entire length of the gutters.
Liquid Rubber Spot Repairs
Coatings over the eave edge to internal gutter area, which initially had blistering and exposed pockets running the length of the system.
Liquid Rubber Spot Repair Coating
Closeup of the coatings at the gutter-eave connection.
< End of Report > CONTACT US Call our 24 hour emergency roof repair at 1.780.424.7663. Mail to: 3428 99 Street NW Edmonton, Alberta T6E-5X5. For all other areas of Canada call us at 1.877.497.3528 toll-free. We service all of Alberta including Edmonton, Stony Plain, Spruce Grove, Fort Saskatchewan, St Albert, Sherwood Park, Leduc, Nisku, Beaumont, Lac La Biche, Grande Prairie, High Level, Westlock, Slave Lake, Edson, Drayton Valley, Devon, Camrose, Wetaskiwin, Tofield, Lamont, Morinville, Vegreville, Tofield, Millet, Calmar, Evansburg, Redwater, Onaway, Viking, Athabasca, High Prairie, Valleyview, Fairview, Peace River, Whitecourt, Mayerthorpe and many more rural areas and towns.

Liquid Rubber Coating Ponoka, June 17, 2015.

Article: Liquid Rubber Coating Ponoka To Industrial Metal Roof.

Below you will find the process of installing a liquid rubber coating.  June 22, 2014: Crew Arrives on Site to Start Detail Work.  Today we did almost all of our seams, corners and details with mesh and liquid rubber. This took some time because all the seams where lifted and really dirty. We had to do them over all the detail and units we had use trowel grade over all them. There was holes and voids throughout them. We sealed them with liquid rubber brush grade. I will be returning Monday to finish site.
Liquid Rubber Applied Around Unit
Liquid Rubber Applied Around Unit.
Liquid Rubber Applied to Seam
Liquid Rubber Applied to Seam.
Liquid Rubber Detail Work
Liquid Rubber Detail Work.
Liquid Rubber Around Vents
Liquid Rubber Around Vents.
  June 23, 2014: Crew Arrives on Site to Finish Coating.  Today we finished up our prep work. We started rolling rubber, the roof looks really good. I also did the seems in the gutter with mesh and liquid rubber. The roof is 100% complete. Material used. 100 ft of mesh. 6 Pails of brush grade liquid rubber. 2 Pails of trowel grade. 6 paint brushes. 3 rollers and roller cages.
Liquid Rubber Coating
Liquid Rubber Coating
Roof Half Rolled With Liquid Rubber
Roof Half Rolled With Liquid Rubber
Liquid Rubber
Liquid Rubber to lower roof over office.
Liquid Rubber Coating Ponoka
Liquid Rubber Coating Ponoka
  < End of Report > CONTACT US Call our 24 hour emergency roof repair at 1.780.424.7663. Mail to: 3428 99 Street NW Edmonton, Alberta T6E-5X5. For all other areas of Canada call us at 1.877.497.3528 toll-free. We service all of Alberta including Edmonton, Stony Plain, Spruce Grove, Fort Saskatchewan, St Albert, Sherwood Park, Leduc, Nisku, Beaumont, Lac La Biche, Grande Prairie, High Level, Westlock, Slave Lake, Edson, Drayton Valley, Devon, Camrose, Wetaskiwin, Tofield, Lamont, Morinville, Vegreville, Tofield, Millet, Calmar, Evansburg, Redwater, Onaway, Viking, Athabasca, High Prairie, Valleyview, Fairview, Peace River, Whitecourt, Mayerthorpe and many more rural areas and towns.  

Roof Coating Edmonton. Metal Roof. June 15, 2015.

Article: Industrial Liquid Rubber Metal Roof Coating Edmonton, Alberta.

The roof report below outlines the application scope of work for a liquid rubber roof coating to an industrial standing seam metal roof in Edmonton, Alberta. Roof Coating Edmonton. Roof coatings have been around almost as long as metal roofing has. At issue however, especially in Canada, is finding a roof coating that actually performs to its suitable use and purpose. The purpose of a roof coating is to extend the life of your metal roof and to provide leak free service during that extension of time.
If the coating doesn't provide leak free service and does not therefore extend the life-cycle of your metal roof your money is then lost.
There are two primary reasons roof coatings (specifically in Canada) typically do not fulfill expectations. The first reason is that many of the coatings that are used in Canada are not designed for the harsh weather we have in Canada - specifically the cold temperatures, brutal damage caused by ice dams and the weight of snow loads. The other reason is that the coating itself is just part of the job. In other words, the whole scope of work is what makes a roof coating work properly.
Applying the coating is just a small part of a successful roof coating.
To understand the full scope of work required in Canada for a roof coating to be successful, visit this link to our local Edmonton Roof Repair website and watch the metal roof coating video. It explains in detail what is required for a roof coating in Canada to work. Our roof coatings extend the country from the west coast to eastern Canada and everywhere between. We now coat millions of square feet of liquid rubber in Canada and our crews have become leaders in the industry as a result. I can confidently state the we are one of, if not the largest roof coating companies in Canada. Our clients include everyone from farm owners, acreages, mills, large commercial operations to industrial complexes to oil and gas sites. We have coatings on buildings at mines in the mountains, mills, on tanks, in ponds, on roofs, on foundations, industrial gutters, waterproofing walls and almost everywhere you could image waterproofing to be required. Below is a report from Edmonton, Alberta. In 2013 this client asked us to perform spot roof repairs with liquid rubber to the lower metal roof. The next year (in 2014) they had us back to do spot repairs to the larger upper metal roof at their plant and to coat the complete lower roof included an internal hidden gutter. To this point we haven't had a call-back for any leaks and the customer is very satisfied with the result. August 22, 2014: Roof Coating Crew Arrives First Day For Work.  Site Location: 5604 59 Street NW Edmonton, Alberta. We accomplished getting all the units except for one and all the penetrations waterproofed on the upper shop roof with liquid rubber and mesh and/or seam tape (which was 18 units and about 50 penetrations). All units where meshed and sealed with liquid rubber. Tomorrow we will get all the metal roof seams waterproofed (which is about 2100 lineal feet) and we probably won't start the office roof coating until late tomorrow.
Roof Coating Edmonton, Alberta. Liquid Rubber. Metal Roof. Industrial.
Roof Coating Edmonton, Alberta. Liquid Rubber. Metal Roof. Industrial. Before photo.
Metal Roof - Roof Coating Edmonton, Alberta.
Metal Roof - Roof Coating Edmonton, Alberta.
Old Patch Work to roof that cracked and peeled (asphalt product).
Old Patch Work to roof that cracked and peeled (asphalt product).
Full Roof photo of lower office roof. Liquid rubber prep started at seam.
Full Roof photo of lower office roof. Liquid rubber prep started at seam.
Crew Member Starting Liquid Rubber Meshing Around Unit
Crew Member Starting Liquid Rubber Meshing Around Unit
  August 24, 2014: Crew Arrives Back On Site.  Today the crew got almost all the seams on the upper shop roof all sealed in with liquid rubber, and the bad ones with mesh and liquid rubber. I have about 150 feet left to finish in the morning and then we will be starting the coating on the lower office roof.
Mesh Before Liquid Rubber
Mesh Before Liquid Rubber
Liquid Rubber
Liquid Rubber
Liquid Rubber Around Penitration
Liquid Rubber Around Penetration
Liquid Rubber Seam
Liquid Rubber Seam
  August 25, 2014: Crew Arrives Back On Site. Today we finished all the units and penetrations on the office roof. We also got half the roof rolled (coated). We are on schedule for site completion tomorrow.
Liquid Rubber Half The Roof Completed
Liquid Rubber Half The Roof Completed
Liquid Rubber To Metal
Liquid Rubber To Metal
Liquid Rubber Coating To Half The Roof
Liquid Rubber Coating To Half The Roof
Liquid Rubber Coating
Liquid Rubber Coating
  August 26, 2014: Crew Arrives On Site And Completes Job.  Today we were down a guy, but we managed to finish the lower shop roof coating completely. When job was finished I did a site walk through with the customer and he was very happy with the work.
Liquid Rubber Coating Completed
Liquid Rubber Coating Completed
Liquid Rubber Coating In Edmonton
Liquid Rubber Coating In Edmonton
Liquid Rubber To Commercial Building
Liquid Rubber To Industrial Building Lower Roof
Liquid Rubber Coating
Liquid Rubber Coating
  < End of Report >   CONTACT US Call our 24 hour emergency roof repair at 1.780.424.7663. Mail to: 3428 99 Street NW Edmonton, Alberta T6E-5X5. We service all of Alberta including Edmonton, Stony Plain, Spruce Grove, Fort Saskatchewan, St Albert, Sherwood Park, Leduc, Nisku, Beaumont, Lac La Biche, Grande Prairie, High Level, Westlock, Slave Lake, Edson, Drayton Valley, Devon, Camrose, Wetaskiwin, Tofield, Lamont, Morinville, Vegreville, Tofield, Millet, Calmar, Evansburg, Redwater, Onaway, Viking, Athabasca, High Prairie, Valleyview, Fairview, Peace River, Whitecourt, Mayerthorpe and many more rural areas and towns.