Edmonton Roofing Replacement, December 2014

This report details a residential roofing replacement as well as an initial quotation with various options for the client. The roof had water leakage due to issues with the sealants and draining systems. Additionally the roof was found to be blistering and splitting in areas. The initial email sent from our project manager to the client:
Good morning, Please find attached the quotation options for various membranes for the roof over your garage per the inspection report from our Red Seal Journeyman (see report below my signature at bottom of this email and quotation as attached). Unfortunately because of the small size the per sq rate is significantly higher than if you were to do both your house and garage - so if your house may be a consideration let me know and I'll revise the pricing for you. I've included options for replacement of all membrane types. Once you have had opportunity to review give me a call or email and I'll assist you with any questions you may have. Thanks again for your consideration!

The following is an inspection report from one of our crew members who inspected the site initially: The biggest problem for this house is that they have only one 2 5/8 drain for 3/4's of the roofs.  During heavy rainfall water pours over the edge of the parapet. There is a large amount of water ponding which has reduced the life span of the torch on roof. There is also moisture inside the system and it is apparent that the fiber board laps are beginning to buckle. The sloped roof on the house is in okay condition and will last another five years however the flat roof on the garage will not make it another two. There are signs of rot near the drain on the roof of the garage (there is already a BUR roof and torch on roof on top). I do not recommend a recovery on this roof because of weight issues during the winter, and because of the rotten substrate which will cause issues with attaching another roof. The lower flat roof is 1300 square ft. and the long side is 48 ft. I have given the client two options with the drainage: he can go with a drip edge into a gutter with two drains along the long side, or go with two drop drains in the low spots through the soffit. If we decide to go with the gutter on a new roof, we should add a 1% slope package on a torch-on system. If going with drop drains we should go for a new roof with a EPDM system. Regardless, the old roof needs to be removed to inspect the plywood substrate (in order to deliver a 20 year roof which he is looking for). 
With either drainage we are going to need approximately 100 ft. of downspout and nineties to run the water to the back alley and away from the house.

Materials Required:
  • 20 x 100 ft. 60 mil EPDM.
  • 10 x 100 ft. 6 mil Poly.
  • 90 sheets of 2 inch iso.
  • 45 sheets of 1/2 inch secure rock.
  • 4x 5 gallon pails of bonding adhesive.
  • 1x 3 gallon pail of splice adhesive.
  • 1x 3 gallon pail of quick prime.
  • 1x 5 gallon pail of splice wash.
  • 10 tubes of lap sealant.
  • 2x tubes of caulking.
  • 2x 6 inch rolls of seam tape.
  • 1 roll of form flash.
  • 1 box of rags.
  • 1 scrub pad kit.
  • 8 roller sleeves.
  • 8x 4 inch paint brushes.
  • 1 roll of garbage bags.
  • 600x 3 inch hd fasteners.
  • 600x 3 inch plates.
  • 40 sheets of plywood.
  • 100x 3/4 inch deck screws.
  • 100 ft. of drip edge.
  • 12 ft. of flashing for the chimney and smack pins.
  • 48 ft. of 5 inch brown gutters with hardware and matching gutter guards.
  • 100 ft. of down spout.
  • 10x 90 degree down spout and hangers.
  • 100x self taping brown sheet metal screws.
  • 2 rolls of 250 grey cap.
  • 1 roll of flam flam.
  • 1 can of spray primer.

Daily Report for Dec 4, 2014: The crew arrived at 7:30am to lay down the iso board as well as the rubber bug. At 5:00pm it started to snow so the crew left the site for the day.
Daily Report for Dec 5, 2014: Arrived on site at 9:00am to determine the best way to apply the liquid rubber. The client was also on site and had many questions so some time was spent talking with the client. Most of the day was used to install the liquid rubber. Daily Report for Dec 7, 2014: Arrived at 8:00am and spent most of the day installing the metal. There was some detail work to do around the perimeter and the chimney. The lap seal was also installed. The crew did a walk-around with the client who is satisfied with the work done so far. The gutter still needs to be installed. Daily Report for Dec 12, 2014: Gutter is installed and the job is 100% complete.
< End Report > CODE: 1461 Contact Us Call our 24 hour emergency roof repair at 1.780.424.7663. Mail to: 3428 99 Street NW Edmonton, Alberta T6E-5X5. We service all of Alberta including Edmonton, Stony Plain, Spruce Grove, Fort Saskatchewan, St Albert, Sherwood Park, Leduc, Nisku, Beaumont, Lac La Biche, Grande Prairie, High Level, Westlock, Slave Lake, Edson, Drayton Valley, Devon, Camrose, Wetaskiwin, Tofield, Lamont, Morinville, Vegreville, Tofield, Millet, Calmar, Evansburg, Redwater, Onaway, Viking, Athabasca, High Prairie, Valleyview, Fairview, Peace River, Whitecourt, Mayerthorpe and many more rural areas and towns.

Commercial Roof Leak Repair and EPDM Recovery in Edmonton AB, Nov 27 2014

Below you will find a report from the Edmonton roofing repair crew responding to a leak call from a commercial client.  Quotation, September 10 2014:
  • Repair four leaks on tar and gravel roof
  • Complete roof replacement options: Spray foam only (+ top coating as required - polyurea, liquid rubber, or EPDM), TPO or PVC (white reflective roof), 2-ply SBS modified bitumen (torch-on) or 4-ply BUR, 4-ply engineered liquid rubber roof, TOUGH ROOF
  • Sustainable roofing recovery (overlay/reconditioning): Spray foam only, EPDM, TPO or PVC, 2-ply SBS modified bitumen, 1-ply coat tar, 2-ply engineered liquid rubber
Assessment, November 27 2014: We arrived at 8:00 am and searched for roof leaks around the unit for two hours. With no luck, there was still the remaining task of installing the last drain unit over another one of the units which needed work. The roof on the second building is a 28 ft. x 44 ft. BUR roof on a wood deck that leaks in too many places to fix. One drain on the northwest corner and three other penetrations, as well as two vents and a motor exhaust are going through the roof. There is a 4 in. wood detail around the edge and one scupper. We suggest an EPDM roof recovery. The maintenance manager for the site also gave us a call to tell us that a leak was found on the west wall of the building. The crew found numerous rips in the roof along the membrane; it had been completely separated from the drain. Scope of Work:
  • Gum patches to three or more areas
  • Replace the drain with a new 3 in. unit
  • Roof replacement using an SBS 2 ply system
  • Estimated time: 20 hours

Materials:

  • 5 ft. of cap
  • 5 ft. of base
  • 1x can of spray primer
  • 1x 3 in. drain
  • 1 can of mastic
  • 1x roll of 6 in. reinforcement mesh
Code: 14630 Article Topics: Commercial Roof Leak Repair Edmonton. Roof Drain Repair.   Contact Us Call our 24 hour emergency roof repair at 1.780.424.7663. Mail to: 3428 99 Street NW Edmonton, Alberta T6E-5X5. We service all of Alberta including Edmonton, Stony Plain, Spruce Grove, Fort Saskatchewan, St Albert, Sherwood Park, Leduc, Nisku, Beaumont, Lac La Biche, Grande Prairie, High Level, Westlock, Slave Lake, Edson, Drayton Valley, Devon, Camrose, Wetaskiwin, Tofield, Lamont, Morinville, Vegreville, Tofield, Millet, Calmar, Evansburg, Redwater, Onaway, Viking, Athabasca, High Prairie, Valleyview, Fairview, Peace River, Whitecourt, Mayerthorpe and many more rural areas and towns.

Saskatoon Commercial Flat Roof Quotation, November 2014

This commercial client in Saskatoon required an inspection and comprehensive quotation because of water damage in the building. As the roof would have to be re-sloped, repairs are not a viable option. Inspection Notes: A site inspection was done on November 26th, 2014 by a GRS representative in Saskatoon and the following was observed: 1. The roof access from the interior is through a closet sided door opening to a wall mounted ladder up to the roof hatch which is approximately 2 square ft. 2. The roof drain directly next to the hatch is dry while the perimeter of the center enclosure is retaining water which is now frozen, indicating a reverse inclination. 3. The suite or suites experiencing the water damage leaking were not inspected as prior arrangements had not been made at the time of this visit. Further, the management on site believed the windows to the suite were leaking and that the maintenance man would be doing further inspection of such. Should a closer inspection be required to obtain greater clarity of the damage and possible solutions an additional site visit would have to be arranged to gain access. 20141126_145833 20141126_145842 20141126_150000 20141126_150012 20141126_150036 20141126_150058 20141126_150106 20141126_150119 20141126_150134 20141126_150140 20141126_150153 20141126_150212 20141126_150226 20141126_150234 20141126_150258 20141126_150308 20141126_150320 20141126_150331 20141126_150344 20141126_150351 20141126_150405 20141126_150414 20141126_150423 20141126_150432 20141126_150436 20141126_150440 20141126_150459 20141126_150522 20141126_150550 20141126_150557 20141126_150601 20141126_150610 20141126_150620 20141126_150633 20141126_150643 20141126_150655 20141126_150703 20141126_150715 20141126_150742 20141126_150805 20141126_150820 20141126_150833 20141126_150849 The client was presented with a comprehensive quotation involving various replacement or recovery options. This file may be updated at a later date. < End Report > CODE: 241 Contact Us Call our 24 hour emergency roof repair at 1.780.424.7663. Mail to: 3428 99 Street NW Edmonton, Alberta T6E-5X5. We service all of Alberta including Edmonton, Stony Plain, Spruce Grove, Fort Saskatchewan, St Albert, Sherwood Park, Leduc, Nisku, Beaumont, Lac La Biche, Grande Prairie, High Level, Westlock, Slave Lake, Edson, Drayton Valley, Devon, Camrose, Wetaskiwin, Tofield, Lamont, Morinville, Vegreville, Tofield, Millet, Calmar, Evansburg, Redwater, Onaway, Viking, Athabasca, High Prairie, Valleyview, Fairview, Peace River, Whitecourt, Mayerthorpe and many more rural areas and towns.

High River SBS Roof Replacement, October 2014

This commercial client required a roof replacement and elected to have GRS install a 2-ply SBS Modified Bitumen system. This was done in High River, AB, far to the north of the province.   Roof Report: October 24, 2014 The team arrived on site for 9am and began to get it prepared to commence work the following day. Material lists were organized and ready for purchase, and the tools were loaded onto the roof. The crew waited for the dump bin to arrive, and once it had they went off to the store to pick up the last of the materials needed for the job's beginning. They ended the day for 3:00pm, leaving the job site for the evening.   Roof Report: October 26, 2011 The four team members arrived for 8:00am and worked for a few short hours until 11:30. In their time on site, they stripped off the torch-on system and moved materials to the side of the roof where they would begin work the following day. The weather forecast called for heavy snow, and ice crystals were building on the roof even after torching. They called it for the day at 11:30am, and would return the following morning.   Roof Report: October 29, 2015 Starting the morning at 7:30, the team got to work with chipping away ice, blow-drying the roof, and cleaning it off for work. Once done, they got to stripping outer walls, putting up around 25' of fascia, and stripping the parapet walls too. They installed two high domes and starting putting more capping on. Heavy snowfall came in just before 5:00pm, so the team wrapped up the site for the day.   Updated Quotation Delivered: October 30, 2014 We sent over an updated quote to the client to show payments that had been applied to date. There was some uncertainty remaining about the amount of sheathing requiring replacement, so the final quote was yet to be confirmed.   Roof Report: October 30, 2014 This day saw a lot of ice chipped away and snow swept off of the roof. They team torched the capping and installed scupper drains and the necessary downpipes. They left the job site for 4:00pm once word arrived that some more of the materials for the job site on order had arrived. They got the materials and returned to the town; an 8-hour round trip. Roof Report: October 31, 2014 There was some light rain in the morning, but not enough to cancel the day's progress. The rest of the roof system was ripped off and the rotten plywood underneath replaced. The last scupper drain was installed, and some more of the parapet wall was stripped. Once done, the last of the capping was torched on and materials were moved and prepared for the next day. After clean-up, the team departed the site for around 5:30pm. The day's efforts saw 25 sheets of OSB plywood 7/16 installed, which allowed for a final quote to be delivered to the client as everything that would be exposed and inspected had been so. High Level-20141031-03223 High Level-20141025-03127       Roof Report: November 2, 2014 This day, the team met on the roof for 8:00am and got to work. Their task for the day was working on getting the enco new paper was completed, and the job site was cleaned up afterwards. They left the site at 1:00pm, another job completed.     CODE: 10006 Contact Us Call our 24 hour emergency roof repair at 1.780.424.7663. Mail to: 3428 99 Street NW Edmonton, Alberta T6E-5X5. We service all of Alberta including Edmonton, Stony Plain, Spruce Grove, Fort Saskatchewan, St Albert, Sherwood Park, Leduc, Nisku, Beaumont, Lac La Biche, Grande Prairie, High Level, Westlock, Slave Lake, Edson, Drayton Valley, Devon, Camrose, Wetaskiwin, Tofield, Lamont, Morinville, Vegreville, Tofield, Millet, Calmar, Evansburg, Redwater, Onaway, Viking, Athabasca, High Prairie, Valleyview, Fairview, Peace River, Whitecourt, Mayerthorpe and many more rural areas and towns.

Fort Saskatchewan Roof Leak Inspection, October 2014

This report outlines an inspection carried out by the GRS team for a client in Fort Saskatchewan. The location of the water leak was determined and a recommendation was made for the necessary repairs. Inspection, October 30, 2014:
This client has a leak in the SW corner of the hotel roof. While on the roof I looked through all of the laps in the area where it was leaking, (and on the top side of the slope that would have run through the area) and they were all okay. I did find a couple of breaches in the system. One I fixed with TPO cover strip and the other with water cut off. I think the leak is coming from the stucco to the frame work as there are cracks and holes through it. There is also an electrical conduit that runs along the parapet walls which is mechanically fastened. The conduit is attached with 1 inch screws and they are popping out, this should be fixed to prevent any further breaches to the system.
20141030_103954_resized 20141030_110931_resized 20141030_111056_resized 20141030_111102_resized 20141030_111129_resized 20141030_111140_resized 20141030_111453_resized_1 20141030_113109_resized 20141030_113147_resized 20141030_113152_resized 20141030_113155_resized 20141030_113205_resized 20141030_113349_resized 20141030_113638_resized 20141030_113801_resized 20141030_113842_resized
< End Report > CODE: 10120 Contact Us Call our 24 hour emergency roof repair at 1.780.424.7663. Mail to: 3428 99 Street NW Edmonton, Alberta T6E-5X5. We service all of Alberta including Edmonton, Stony Plain, Spruce Grove, Fort Saskatchewan, St Albert, Sherwood Park, Leduc, Nisku, Beaumont, Lac La Biche, Grande Prairie, High Level, Westlock, Slave Lake, Edson, Drayton Valley, Devon, Camrose, Wetaskiwin, Tofield, Lamont, Morinville, Vegreville, Tofield, Millet, Calmar, Evansburg, Redwater, Onaway, Viking, Athabasca, High Prairie, Valleyview, Fairview, Peace River, Whitecourt, Mayerthorpe and many more rural areas and towns.

Engineered Liquid Rubber Roof Recovery in Edmonton AB, October 2014

Below you will find a quotation, project manager notes, and a field report for an engineered liquid rubber roof recovery for an industrial metal roofing client in Edmonton, Alberta. Quotation, October 15 2014:
  • Engineered liquid rubber recovery to complete metal roof.
  • Pressure washing to clean, water test, and assess.
  • Fasteners will be tested and replaced as required to complete the roof deck, penetrations, and gutters.
  • Sheet metal repair and penetration saddle fabrication as required.
  • Remove old caulking as required.
  • Hand trowel all penetrations, roof to wall connections, fasteners, ridge, horizontal sheet seams, hidden gutters, and roof edge at external gutters with mesh and high grade rubber as required.
  • Apply liquid rubber coating, allow cure time, repeat hand trowel process above, and apply second coat of liquid rubber.
  • Liquid rubber to full inside face of parapet and top of parapet cap.
  • Ten year manufacturer warranty is extendable to twenty year maintenance agreement.
Project Manager Notes This roof structure may be a candidate for either a repair-maintenance program or an engineered liquid rubber coating - you may not have to replace it. I would not recommend a standard reflective elastomeric coating, or the SPF spray foam (with standard reflective coating), as this standard does not last well in a Western Canadian climate. Liquid rubber performs well in our climate as it has up to a 1200% expansion/contraction rate. If considering SPF for R-value, we strongly suggest covering the spray foam with liquid rubber or EPDM. Our crews do this work everyday with success. Generally speaking, metal roof systems are constant aggravating roof structures. Industrial systems have a deficient design - they are water-shedding, and not waterproofing, coverings. Metal expands and contracts more than any other roofing material and tend to leak from ice/snow loads. Leaks are also intermittent at seams (vertically where sheets are seamed together and horizontally where seams meet between sheets), penetrations, fasteners, around the perimeters at gutters, under the eaves, and at joints between roof and wall connections. Rust and corrosion may also develop. Traditional caulking or coating lasts a few seasons at best. Remedies are either spot repairs - maintenance with caulking or engineered coatings. Our recommendation in this instance is a high and engineered 2-ply liquid rubber polymer coating with a 10 year warranty, with the option of a 20 year maintenance contract for extended leak protection. Our client approved the quotation the same day for a roof recovery. Field Report, October 22 2014: After picking up the liquid rubber, we went to the work site and prepared the roof with seam tape around all seam tapes and penetrations. We then began coating the roof with liquid rubber and completed this site by the evening.
20141020_141353_resized
Seam taping around units
20141020_164201_resized
Coating begins
20141020_141400_resized
Assessment
20141020_141654_resized
Scoping ventilation units
20141020_141701_resized
Low-slope valleys
20141020_141707_resized
20141020_164303_resized
Coating around B-vent
20141020_162526_resized 20141020_164209_resized 20141020_164217_resized liquid 20141020_164257_resized 20141020_164320_resized 20141021_150726_resized 20141021_150734_resized 20141021_150743_resized < End Report > Code: 9222 Article Topics: Industrial Metal Roof Coating Edmonton, Alberta. Liquid Rubber.   Contact Us 24 Hour Emergency Roof Repair. Telephone: 1.403.873.7663. Email: info@calgaryroofrepair.ca. Mailing: 240 – 70 Shawville Boulevard SE Calgary, Alberta. T2Y 2Z3. For all other areas of Canada call 1.877.497.3528 Toll Free. We service all areas of southern and central Alberta and south east British Columbia including Airdrie, Banff, Calgary, Canmore, Crossfield, Carstairs, Didsbury, Olds, Sundre, Three Hills, Drumheller, Hanna, Brooks, Bassano, Strathmore, Chestermere, Irricana, Cochrane, Black Diamond, Okotoks, Priddis, Bragg Creek, Cranbrook, Fernie, Panorama, High River, Vulcan, Medicine Hat, Lethbridge, Taber, Sylvan Lake, Red Deer and other Alberta rural points between.

Edmonton Commercial Roof Penetration Install, October 2014

This commercial client reached out to us about having two roof penetrations installed properly on their EPDM roof. The roof was very muddy and needed to be cleaned before the installation could begin. Photos sent by the client showing the roof penetrations: 20140814_102849_resized 20140814_102930_resized Roof Report, October 17th, 2014:
This was an EPDM roof which the client needed two penetrations installed on. The roof was very dirty and covered in mud which took some time to clean. They had used silicone to put a temporary seal which we had to remove once we had cleaned the area. We roofed it in with form flash and the job is now 100% complete. This was an hourly dispatch plus materials.
Materials Used:
  • 24ft. of 12 inch form flash.
  • 1 can of primer.
  • 1 bag of rags.
  • (1) 1 gallon can of splice wash.
  • 2 tubes of lap seal.
20141016_142913_resized 20141016_142922_resized 20141016_142946_resized 20141016_160512_resized 20141016_173518_resized 20141016_173525_resized 20141016_173534_resized 20141016_173542_resized < End Report > CODE: 9503 Contact Us Call our 24 hour emergency roof repair at 1.780.424.7663. Mail to: 3428 99 Street NW Edmonton, Alberta T6E-5X5. We service all of Alberta including Edmonton, Stony Plain, Spruce Grove, Fort Saskatchewan, St Albert, Sherwood Park, Leduc, Nisku, Beaumont, Lac La Biche, Grande Prairie, High Level, Westlock, Slave Lake, Edson, Drayton Valley, Devon, Camrose, Wetaskiwin, Tofield, Lamont, Morinville, Vegreville, Tofield, Millet, Calmar, Evansburg, Redwater, Onaway, Viking, Athabasca, High Prairie, Valleyview, Fairview, Peace River, Whitecourt, Mayerthorpe and many more rural areas and towns.

Edmonton Residential Flat Roof Maintenance, September to October 2014

Below you will find an assessment, field reports, and photo journal from the Edmonton roofing repair crew for a maintenance on a residential flat roof. The roofing system is due for replacement, but required immediate leak repairs and vent installations. Assessment, September 24 2014: The roof is a low-slope system with existing tar and gravel. There is an approximately 3 in. insulation on top of the plywood roofing below the tar and gravel. The client would like some insulation of their patched areas. The roof was installed in 1981 and needs to be replaced soon. There have been no leaks to date.
  1. There are two holes that need to be filled in - one where the old chimney was and the other where there was formerly a kitchen exhaust. Everything below the roof line has been removed, so the scope involves removing metal roof caps and installing pieces of plywood, insulation, and roof membrane.
  2. There is one hole in the roof requiring a new range hood. An HVAC contractor has already marked out a location on a roof where this hood will be installed. The hole needs to be 7 in. in diameter. The ducting requires installation and sealing.
  3. There is a small 2' x 12' addition over the front stairs that needs a roof membrane. There is no need to insulate this area, as it is just over the exterior stairs.
  4. There are two plumbing vents approximately 4 in. in diameter that need to be cut off and sealed.
Field Report, October 8 2014: The scope of worked was changed slightly. Rather than eliminating three vents, one was eliminated and covered in the drilled hole marked by the HVAC contractor. Another vent was then sealed that was leaking. I also ripped an old vent off and replaced it with a new one supplied by the customer. When our other crew member arrived back on-site with SOPRAMASTIC, we sealed all the vents in. Afterwards, we started work on the overhang above the front door. A drip edge was installed around the perimeter along with a 3 inch sheet metal angle at the wall connection. Seam tape was then applied all around it to get a good seal as we glued to the plywood surface. Finally, EPDM was glued down near the end of the day. Materials
  • 2x cans of SOPRAMASTIC three-gallon
  • 14 ft. of EPDM
  • 1x roll of 6 in. mesh.
Field Report, October 9 2014: We finished off the drip edge with seam tape, rolled it in, and then cut our access-rubber off. At this point, the site was completed. We cleaned up the area and left. 20141008_121414_resized 20141008_121419_resized 20141008_122945_resized 20141008_135902_resized 20141008_135907_resized 20141008_135908_resized 20141008_135918_resized 20141008_135936_resized 20141008_135939_resized 20141008_135942_resized 20141008_135946_resized 20141008_142231_resized 20141008_142234_resized 20141008_142236_resized 20141008_142239_resized 20141008_142301_resized 20141008_152424_resized20141008_152424_resized_1 20141008_152430_resized 20141008_152435_resized 20141008_152439_resized 20141008_152445_resized 20141008_153644_resized 20141008_153646_resized 20141008_153649_resized 20141008_153655_resized 20141008_175149_resized < End Report > Code: 9009 Contact Us Call our 24 hour emergency roof repair at 1.780.424.7663. Mail to: 3428 99 Street NW Edmonton, Alberta T6E-5X5. We service all of Alberta including Edmonton, Stony Plain, Spruce Grove, Fort Saskatchewan, St Albert, Sherwood Park, Leduc, Nisku, Beaumont, Lac La Biche, Grande Prairie, High Level, Westlock, Slave Lake, Edson, Drayton Valley, Devon, Camrose, Wetaskiwin, Tofield, Lamont, Morinville, Vegreville, Tofield, Millet, Calmar, Evansburg, Redwater, Onaway, Viking, Athabasca, High Prairie, Valleyview, Fairview, Peace River, Whitecourt, Mayerthorpe and many more rural areas and towns.

Residential Tar and Gravel Flat Roofing Edmonton, October 2014

Article: Tar and Gravel Flat Roofing Edmonton, Residential Roof. Below you will find a report from the flat roofing repair crew in Edmonton Alberta Canada. This crew specializes in repairing flat roofs so the clients can get maximum life out of there roofing systems.  October 7, 2014: Crew Arrives for  Roofing Assessment and Material Check.  October 8, 2014: Crew Arrives to do Hourly Roofing Repairs.  The client changed the scope of work a little bit. Rather than the elimination of three vents, I eliminated one vent and covered it over. I added a new vent by drilling a hole and putting a vent above it it was piped in from the HVAC guys, I also sealed another vent that was existing already but was leaking. We then ripped an old vent off and replaced with a new one supplied by customer.
Flat Roof Vent Repair
Flat Roof Vent Repair
Deleted Vent
Deleted Vent
Drain Repair
Drain Repair
Drain
Drain
Tar And Gravel Flat Roof Repair
Exposed drain after tar and gravel removal
< End Report > CONTACT US Call our 24 hour emergency roof repair at 1.780.424.7663. Mail to: 3428 99 Street NW Edmonton, Alberta T6E-5X5. We service all of Alberta including Edmonton, Stony Plain, Spruce Grove, Fort Saskatchewan, St Albert, Sherwood Park, Leduc, Nisku, Beaumont, Lac La Biche, Grande Prairie, High Level, Westlock, Slave Lake, Edson, Drayton Valley, Devon, Camrose, Wetaskiwin, Tofield, Lamont, Morinville, Vegreville, Tofield, Millet, Calmar, Evansburg, Redwater, Onaway, Viking, Athabasca, High Prairie, Valleyview, Fairview, Peace River, Whitecourt, Mayerthorpe and many more rural areas and towns.   Code: 9009

Roof Vent Shingle Repair Edmonton, September 2014

The brief report below follows a repair made to this residential client's bathroom vent on a shingle roof. The old shingles had been lifting up, so, once they were replaced, everything was resolved quickly. Continue reading Roof Vent Shingle Repair Edmonton, September 2014